Onkyo AV RECEIVER HT-RC460 - Manual (Page 51)

Advanced Operations
En-51
■ LPF of LFE
(Low-Pass Filter for the LFE Channel)
` 80Hz, 90Hz, 100Hz, 120Hz
` Off:
Low-Pass Filter is not applied.
With this setting, you can specify the cutoff frequency of
the LFE channel’s low-pass filter (LPF), which can be
used to filter out unwanted hum. The LPF only applies to
sources that use the LFE channel.
■ Double Bass
` On
` Off
Turn this setting on to boost bass output by feeding bass
sounds from the front left, right, and center channels to
the subwoofer.
Note
• When the “Subwoofer” setting is set to “No” or the “Front”
setting to anything other than “Full Band”, this setting is fixed to
“- - -”.
• This setting is set to “On” automatically when the “Subwoofer”
and “Front” settings are set for the first time to “Yes” and “Full
Band” respectively.
Speaker Distance
Here you can specify the distance from each speaker to the
listening position so that the sound from each speaker
arrives at the listener’s ears as the sound designer intended.
■ Unit
` feet :
Distances can be set in feet. Range: 1.0ft to 30.0ft in
1.0 foot steps.
` meters:
Distances can be set in meters. Range: 0.30m to
9.00m in 0.30 meter steps.
■ Left, Front High Left, Center, Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left, Subwoofer
` Specify the distance from each speaker to your
listening position.
Note
• Speakers that you set to “No” or “None” in
“Speaker Configuration” cannot be selected ( ➔ page 50 ).
• When the “Powered Zone 2” setting is set to “Yes” and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
Level Calibration
Here you can adjust the level of each speaker with the
built-in test tone so that the volume of each speaker is the
same at the listening position.
Note
• These settings cannot be calibrated in either of the following
cases:
– The “Audio TV Out” setting is set to “On” (
➔ page 60 ).
– “HDMI Control(RIHD)” is set to “On” ( ➔ page 60 ) and
you’re listening through your TV speakers.
– The AV receiver is muted.
■ Left, Front High Left, Center *1 , Front High Right,
Right, Surround Right, Surround Back Right,
Surround Back Left, Surround Left
` –12dB to 0dB to +12dB in 1 dB steps.
■ Subwoofer *1
` –15dB to 0dB to +12dB in 1 dB steps.
Note
• Speakers that you set to “No” or “None” in
“Speaker Configuration” cannot be selected ( ➔ page 50 ).
• When the “Powered Zone 2” setting is set to “Yes” and Zone 2
is turned on, the surround back and front high speakers cannot be
used.
*1 For the center speaker and subwoofer, the level settings made
by using the Quick Setup are saved in this menu (
➔ page 44 ).
Tip
• If you’re using a handheld sound level meter, adjust the level of
each speaker so that it reads 75 dB SPL at the listening position,
measured with C-weighting and slow reading.
This setting is NOT set automatically by
Audyssey 2EQ
® Room Correction and Speaker Setup
( ➔ page 32 ).
This setting is set automatically by Audyssey 2EQ Room
Correction and Speaker Setup (
➔ page 32 ).
This setting is set automatically by Audyssey 2EQ Room
Correction and Speaker Setup (
➔ page 32 ).