Output Solutions C I - 8 0 6 0 - Manual (Page 51)

Configuring the Printer
3-3
3.2 Standard Configuration
The standard Configuration (factory default values) is reflected in the following
pintout.
PRINT OUT FW-VERSION 20xxxxxx HW-VERSION 29xxxxxx FPGA 4.7 PAGE COUNT 50
INTERFACE
I/F TYPE PARALL./RS232
WORD LENGTH 8 BIT
BAUD-RATE 9600 BIT/S
PARITY BIT EVEN
PROTOCOL DTR
DSR/CTS MODE IGNOR. DSR+CTS
I/F BUFFER 8 KBYTE
MENU ACCESS FULL ACCESS
CURRENT SETTINGS MACRO 1* MACRO 2 MACRO 3 MACRO 4
PAPER SOURCEE TRACTOR LOWER TRACTOR LOWER TRACTOR LOWER TRACTOR LOWER TRACTOR LOWER
PAPER EXIT
PATH
BATCH BATCH BATCH BATCH BATCH
BATCH CAPACITY - - - - -
PRINT POS. ADJ.
TRACT.L. V-POS
0.0 0.0 0.0 0.0 0.0
TRACT.L. H-POS 0.0 0.0 0.0 0.0 0.0
TRACT.U. V-POS 0.0 0.0 0.0 0.0 0.0
TRACT.U. H-POS 0.0 0.0 0.0 0.0 0.0
MANUAL V-POS 0.0 0.0 0.0 0.0 0.0
MANUAL H-POS 0.0 0.0 0.0 0.0 0.0
BIN 1 V-POS 0.0 0.0 0.0 0.0 0.0
BIN 1 H-POS 0.0 0.0 0.0 0.0 0.0
BIN 2 V-POS 0.0 0.0 0.0 0.0 0.0
BIN 2 H-POS 0.0 0.0 0.0 0.0 0.0
BIN 3 V-POS 0.0 0.0 0.0 0.0 0.0
BIN 3 H-POS 0.0 0.0 0.0 0.0 0.0
PAGE LENGTH 72 LINES 72 LINES 72 LINES 72 LINES 72 LINES
FONT QUALITY LQ LQ LQ LQ LQ
GRAPHICS QUALITY STANDARD STANDARD STANDARD STANDARD STANDARD
FONT DATA DATA DATA DATA DATA
PITCH 10 CPI 10 CPI 10 CPI 10 CPI 10 CPI
LINE 6 LPI 6 LPI 6 LPI 6 LPI 6 LPI
EMULATION EPSON LQ EPSON LQ IBM PROPR. IBM PROPR. AGM EPSON LQ
CARACTER SET EPSON EXT. GCT EPSON EXT. GCT IBM SET 2 IBM SET 2 EPSON EXT. GCT
1: U.S.A. 1: U.S.A. 1: U.S.A. 1: U.S.A. 1: U.S.A.
LEFT MARGIN 1. COLUMNS 1. COLUMNS 1. COLUMNS 1. COLUMNS 1. COLUMNS
RIGHT MARGIN 165. COLUMNS 165. COLUMNS 165. COLUMNS 165. COLUMNS 165. COLUMNS
LINE MODE LF=LF, CR=CR LF=LF, CR=CR LF=LF, CR=CR LF=LF, CR=CR LF=LF, CR=CR
PERF. SKIP YES YES YES YES YES
TEAR-OFF-MODE NO NO NO NO NO
Note: An asterisk (
’) after MACRO 1 indicates the actual macro
The values after FW- and HW-VERSION indicates the actual release.
All this standard settings of the firmware will be restored with the menu function
RECALL FACTORY.