RCA BLD-6HD1 - Manual (Page 4)

5 4
Copying
◆ Switch off all components when connecting or disconnecting cables.
To copy to your video from another video
machine, connect the two machines with a cable
between their RCA sockets and select as
programme "AV" or “F. AV” (front sockets) using
the [AV], [PR+/-], or [00] button.
Set the other video machine to playback and
your machine to record.
To connect a mono audio source, use the front
Audio In socket marked L.
To copy to another video machine from your
video, connect the two machines by means of
their RCA sockets.
On the other video, select its AV input and set the
machine to record.
Switch your video to play back at the position
you want copying to start.
TV
(other VCR)
ANT. OUT
ANT. IN
AUDIO
AUDIO
VIDEO
OUT
IN
L
L
R
R
Other VCR
Decoder for Pay-TV
Camcorder
Video Player
AV
Assembling
For the best results, the source cassette from which you are recording should already be playing back when
you start recording.
Should you wish to assemble your own film, from camcorder footage for example, use the assembly technique
for smooth edit points:
◆ Move the tape to the position at which the new
scene is to be added using the play functions (pages
13-14).
◆ Wind back slightly before the edit point and put the
machine into pause using the
button (do not
press STOP!).
◆ Now go directly into record.
VCR
VCR
VCR 2x
Audio Amp.
devices
To the TV via antenna cable (if you are not using a RCA cable)
◆ If you are using a RCA cable, select the AV input on the TV to see the picture from the video.
◆ If you are not using a RCA cable, select the button number on the TV reserved for video input to see the picture from
the video.
If you are not using a RCA cable, your video can transmit pictures and sound to the TV via the coax aerial cable.
Just tune the TV to the video's transmitting channel (factory set to UHF CH 36). Tune the TV carefully to ensure
the best pictures and sound.
Once you have carried out the steps in "Setting up your
video" (previous page), switch on your TV.
◆ When you install your VCR first time.
Press button of the video’s remote control.
Tune the TV to the ‘LANGUAGE SET’ using the channel
pre-set functions of your TV as described in its manual.
◆ When you install your VCR more than two times. (It
means you have already done the procedure of P.6
‘Tuning the TV’)
Press
button of the video’s remote control.
Tuning the TV to the blue-back screen, if you found blue
back screen on the TV then press MENU button on your
video’s remote control and confirm ‘MAIN MENU’ screen
is appeared, if not tuning the TV again.
Once you have found the picture of above two cases,
follow the instructions within your television manual to
store this new channel into a programme location.
Call the video’s "MAIN MENU" choose
"VCR SETUP" then "RF OUTPUT SET".
Type in the free channel.
Store and exit.
If the quality of the test picture transmitted to the TV is poor due to interference caused by a station transmitting on
channel 36, you can tune the video to a different transmitting channel. Find a free channel between 21 and 69 on your TV.
RF OUTPUT SET
0-9:SELECT (21-69)
OK:CONFIRM MENU:END
CH 36
◆ If the quality of the test picture transmitted to the TV is poor, fine-tuning on the TV may help
(refer to the TV manual).
◆ Without a RCA cable, you will not get stereo sound from a TV capable of stereo sound.
MAIN MENU
TIMER PROGRAM
PR PRESET
VCR SETUP
TAPE CONTROL
PR+/-:SELECT
OK:CONFIRM MENU:END
LANGUAGE SET
ENGLISH
DEUTSCH
ITALIANO
ESPAÑOL
FRANÇAIS
NEDERLANDS
SVENSKA
SUOMI
PR+/-:SELECT
OK:CONFIRM MENU:END