Renesas Emulation Pod M3062NT3-RPD-E - Manual (Page 62)

( 60 / 84 )
Chapter 5. Specifications
5.1 Specifications
Table 5.1 lists the specifications of the M3062NT3-RPD-E.
Table 5.1 Specifications of the M3062NT3-RPD-E
PC4701 (excluding PC4701L and PC4700L)
M16C/62 Group M16C/62N and M16C/30 Group M16C/30L
M30620MCN-001FP x2 (for development tool only)
Single-chip mode, Memory expansion mode, Microprocessor mode
1 MB (Max. operating frequency: 16 MHz. no-wait)
2.2 to 3.6 V
3.0 to 3.6 V: f(XIN) = 16.0 MHz, no-wait
2.4 to 3.6 V: f(XIN) = 7.0 MHz, no-wait
2.2 to 3.6 V: f(XIN) = 3.5 MHz, no-wait
2.2 to 3.6 V: f(XIN) = 7.0 MHz, 1 wait
X
IN
-X
OUT
Internal oscillator circuit board (OSC-3)
Switchable to external oscillator input
X CIN -X COUT Internal oscillator circuit board (fixed 32.768 kHz)
Switchable to external oscillator input
2.7 to 5.5 V
5 to 35 ° C (no dew)
-10 to 60 ° C (no dew)
Supplied from PC4701
100-pin 0.65-mm-pitch LCC socket:
(1) M30800T-PTC (included)
+ IC61-1004-051 (included)
80-pin 0.65-mm-pitch QFP (80P6S-A):
(1) M30800T-PTC (included)
+ M3T-100LCC-DMS (not included)
+ M3T-FLX-DCT613 (not included)
+ M3T-FLX-80QSB (not included)
(2) M30800T-PTC (included)
+ M3T-100LCC-DMS (not included)
+ M3T-FLX-DCT613 (not included)
+ M3T-DIRECT80S (not included)
100-pin 0.65-mm-pitch QFP (100P6S-A):
(1) M30800T-PTC (included)
+ M3T-100LCC-DMS (not included)
+ M3T-DIRECT100S (not included)
(2) M30800T-PTC (included)
+ M3T-100LCC-DMS (not included)
+ M3T-DUMMY100S (not included)
(3) M30800T-PTC (included)
+ M3T-100LCC-DMS (not included)
+ M3T-FLX-100NRB (not included)
100-pin 0.5-mm-pitch LQFP (100P6Q-A):
(1) M3T-F160-100NSD (not included)
(2) M30800T-PTC (included)
+ M3T-100LCC-QSD (not included)
(3) M30800T-PTC (included)
+ M3T-100LCC-DMS (not included)
+ M3T-FLX-100NSD (not included)
100-pin 0.4-mm-pitch TQFP (100PFB-A):
(1) M3T-F160-100NSE (not included)
Emulators
Applicable MCU
Evaluation MCU
Usable mode
Emulation memory
Supported voltage
Maximum operating frequency
Clock supply
Operating voltage
Operating temperature
Storage temperature
Power supply to emulation pod
Connection to target system
Refer to "3.8 Connecting the Target
System" (page 41).