Nikon DSR-1500AP - Manual (Page 61)

61
Menu Contents
C
h
ap
te
r 4
M
e
nu
S
e
tti
n
gs
PLAY START [> PLAY start]: Set the timing for switching from
stop mode to playback mode.
In an editing system including an editing control unit such as
the PVE-500, you can adjust this setting so that the delay
before switching to playback mode is the same on all the decks
of the editing system. It is then no longer necessary to
synchronize the decks for editing, and the preroll time can be
shortened.
16 FRAME DELAY [>> 16 delay] to 4 FRAME DELAY [>> 4
delay]: The larger the numerical value, the longer the
delay.
Factory default setting: 5 FRAME DELAY [>> 5 delay] (for
DSR-1500A) or 4 FRAME DELAY [>> 4 delay] (for DSR-
1500AP)
AUTO REW [> Auto REW]: Select whether to rewind the tape
automatically when recording or playback reaches the end
of a tape.
DISABLE [>> DISABLE]: Do not rewind the tape
automatically.
* ENABLE [>> ENABLE]: Rewind the tape automatically.
A MODE CHANGE [> Aud change]: Determine whether or
not to permit audio insert editing that uses a different audio
recording mode (2- or 4-channel mode) from that which
was used for the tape loaded in the recorder.
Note
This is used when entirely changing the recording audio mode.
At the IN and OUT points, audio recording is muted.
* OFF [>> OFF]: Do not permit.
ON [>> ON]: Permit.
DISPLAY CONTROL [Display]: Settings related to
indications on the monitor and the unit Description of settings
CHARA. DISPLAY [> Chara disp]: Determine whether or not
to output text (such as time code values) from the B −Y/
CPST (SUPER) connector.
OFF [>> OFF]: Do not output text. (In spite of this setting,
pressing the MENU button causes menu text to be
output.)
* ON [>> ON]: Output text.
CHARA. POSITION [> Chara pos]: Set the position of text
superimposed on output from the B −Y/CPST (SUPER)
connector to the monitor.
Use the fFgG buttons in the menu control section to adjust
the text position while watching the monitor screen.
To return to level 1 of the setup menu, press the MENU button.
CHARA. TYPE [> Chara type]: Set the type of characters in
text superimposed on output from the B −Y/CPST
(SUPER) connector to the monitor.
Make the following settings while watching the monitor screen.
*
WHITE (WITH BKGD) [>> White]: White characters on black
background
BLACK (WITH BKGD) [>> Black]: Black characters on white
background
WHITE/OUTLINE [>> W/outline]: White characters with black
outline
BLACK/OUTLINE [>> B/outline]: Black characters with white
outline
CHARA. VSIZE [> Chara size]: Determine the vertical size of
characters such as time code output from the B
−Y/CPST
(SUPER) connector for superimposed display on the
monitor.
Make the selection while watching the monitor screen.
*
X1 [>> X1]: Standard size
X2 [>> X2]: 2 times standard size
DISPLAY INFO [> DISP info]: Select information
superimposed on output from the B −Y/CPST (SUPER)
connector to the monitor.
* TIME DATA & STATUS [>> Time&STA]: Time data and
operating mode indications
TIME DATA & UB [>> Time&UB]: Time data selected using
the COUNTER SELECT button, and user bit data (When
user bit data is selected using the COUNTER SELECT
button, user bit data and time code are shown.)
TIME DATA & CNT [>> Time&CNT]: Time data selected
using the COUNTER SELECT button, and CNT value
(When CNT is selected using the COUNTER SELECT
button, CNT value and time code are shown.)
TIME DATA & TIME[>> Time&Time]: Time data and VITC
TIME DATA ONLY [>> Time]: Time data only
REC DATE & TIME [>> REC Date]: The time data selected
with the COUNTER SELECT button is shown in the time
counter display, and the date and time of recording are
shown on the monitor screen.
OPERATIONAL FUNCTION [Operational]: Operation
settings Description of settings