Niles Audio ZR-4 - Manual (Page 25)

23
NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373
NOTE: IF A CODE DIGIT IS 0, THE LED DOES NOT BLINK
5. Continue through five digits by pressing 2 for the second
digit, 3 for the third, 4 for the fourth and finally 5 for the
fifth; counting the TV Source Key LED blinks for each digit.
6. To check for other device codes, repeat steps 1—5,
substituting the source key for the device you would like
to check
CONFIGURING SOURCES 2,3, AND 4
These source device commands are learned directly from the
original device remotes. There are some precautions to be
observed:
LEARNING PRECAUTIONS
Your original remote control device must be in working order to
learn IR codes properly.
• Learned keys are device specific, so each key can store a
unique function for each device
• Do not use the following keys for learning: Source Keys
or SETUP .
• Learning capacity is approximately 42 to 75 keys,
depending on the code being learned
• Certain device functions cannot be learned, including
multi-frequency types, some high frequency ones, and other
unusual formats
• For optimum learning, avoid high levels of ambient light
such as natural sunlight or energy-efficient fluorescent lights
NOTE: PLEASE HAVE YOUR ORIGINAL REMOTE CONTROLS HANDY
BEFORE PROGRAMMING LEARNING
PROGRAMMING A LEARNED KEY
NOTE: IF MORE THAN 10 SECONDS PASS BETWEEN KEY PRESSES, THE
REMOTE EXITS PROGRAMMING
1. Place the Niles R-6L Hand-Held Learning Remote Control
head-to-head (about 2” apart) from your original
remote control.
2. Locate the key (on your original remote control) that you
want the R-6L to learn.
3. Press the device key for which you wish to learn IR
commands.
4. Press and hold SETUP until the Source Key LED blinks
twice, then release.
5. Enter 9 7 5 . The Source Key LED blinks twice.
NOTE: IF THE LED DISPLAYS ONE LONG FLASH INSTEAD, YOUR
BATTERIES ARE LOW, OR THE R-6L MEMORY IS FULL. IN EITHER
CASE, THE REMOTE CANNOT LEARN A NEW KEY.
6. Press the key on the Niles R-6L remote for which you wish
to learn a command. The Source Key LED will blink rapidly
for three seconds, indicating the remote is ready to learn.
7. On the original device remote, press-and-hold the key
to be learned. Continue holding the key on the original
remote until the R-6L’s Source Key LED blinks twice.
NOTE: IF THE SOURCE KEY LED DISPLAYS ONE LONG BLINK,
A LEARNING ERROR HAS OCCURRED. TRY REPEATING THIS
STEP AGAIN UNTIL A SUCCESSFUL CAPTURE IS OBTAINED.
IF THE FUNCTION IS STILL NOT CAPTURED, PRESS AND
HOLD SETUP TO EXIT PROGRAMMING AND REVIEW THE
“LEARNING PRECAUTIONS” ABOVE. IF NEEDED, ALSO SEE
“TROUBLESHOOTING”. AFTER REVIEW, START PROGRAMMING
AGAIN AT STEP 1.
8. Repeat steps 6 through 7 for each key to be learned.
Once all keys are learned, press-and-hold SETUP until the
Source Key LED blinks twice to save all data learned.
DELETING A SINGLE LEARNED KEY
This process returns a single key to its original programming for the
selected device only. Learned programming can also be deleted
by teaching a different function to the key (see “
PROGRAMMING A
LEARNED KEY ”).
NOTE: IF MORE THAN 10 SECONDS PASS BETWEEN KEY PRESSES, THE
REMOTE EXITS PROGRAMMING.
1. Press the Source Key for the device for which a learned
key is to be deleted.
2. Press-and-hold SETUP until the Source Key LED blinks
twice, then release
3. Enter 9 7 6 . The Source Key LED blinks twice
4. Press the key containing the learned function to be
deleted twice. The Source Key LED blinks twice and the
R-6L exits from programming mode.
DELETING ALL LEARNED KEYS FOR A SPE-
CIFIC DEVICE
NOTE: IF MORE THAN 10 SECONDS PASS BETWEEN KEY PRESSES, THE
REMOTE EXITS PROGRAMMING.
1. Press-and-hold SETUP until a Source Key LED blinks
twice, then release