Niles Audio ZR-4 User Manual

Page 23

(CONTINUED ON NEXT PAGE)

NILES AUDIO CORPORATION – 1-800-BUY-HIFI – 305-238-4373

BASS ADJUSTMENT

A source should be playing through the speakers in the zone. To
set the bass adjustment at a zone keypad press and hold the

Mute

and bottom right

Master

key simultaneously for three seconds. The

bottom right

Master

key LED will be blinking.

Press the

Volume

key to increase the bass or the

Volume

– key to

decrease the bass.

To reset the bass to its default ﬂat setting press-and-hold the

Volume

and

Volume

– keys simultaneously for two seconds.

To save your changes and exit conﬁguration mode simultaneously
press and hold the

Mute

and bottom right

Master

keys for three

seconds. The keypad will return to its previous state.

Repeat these steps for the remaining zone keypads.

TREBLE ADJUSTMENT

A source should be playing through the speakers in the zone. To set
the treble adjustment simultaneously press-and-hold the

Mute

and

bottom left

Master

key on a zone’s keypad for three seconds. The

bottom left

Master

key LED will be blinking.

Press the

Volume

key

to increase the treble or the

Volume

–

key

decrease the treble.

To reset the treble to its default ﬂat setting press-and-hold the

Volume +

and

Volume

–

keys

simultaneously for two seconds.

To save your changes and exit conﬁguration mode simultaneously
press and hold the

Mute

and bottom left

Master

key for three

seconds. The keypad will return to its previous state.

Repeat these steps for the remaining zone, keypads.

IR SENSOR ON/OFF

By factory default the IR sensor is set to the

position.

To turn the keypad’s internal IR sensor on or off simultaneously
press-and-hold the

Mute

and upper right

Master key

for three

seconds. The upper right

Master

key LED will be blinking.

Press the

Volume + key

to turn it on. Press the

Volume

–

key

to turn it off.

To save your changes and exit conﬁguration mode simultaneously
press-and-hold the

Mute

and upper right

Master key

for three

seconds. The keypad will return to its previous state.

Repeat these steps for the remaining zone keypads.

VARIABLE LOUDNESS ON/OFF

By factory default variable loudness is set to the Off position.

To turn the zone’s variable loudness on or off simultaneously press-
and-hold the

Mute

and upper left

Master key

for three seconds. The

upper left

Master key

LED will be blinking.

Press the

Volume

key

to turn it on. Press the

Volume

–

key

to turn it off.

To save your changes and exit conﬁguration mode simultaneously
press-and-hold the

Mute

and upper left

Master key

for three

seconds. The keypad will return to its previous state.

Repeat these steps for the remaining zone keypads.

CONFIGURING THE ZONE

THE HAND-HELD REMOTE

INSTALLING BATTERIES

Your Niles

R-6L Hand-Held Learning Remote Control

requires 2 “AA”

batteries (included).

BATTERY USE AND SAFETY

• Use only fresh batteries of the required size and

recommended type

• Do not mix old and new batteries, different types

of batteries (standard, alkaline, or rechargeable), or
rechargeable batteries of different capacities

• If you do not plan to use the remote for an extended

period, remove the batteries. They can leak chemicals
that can destroy electronic parts

WARNING: DISPOSE OF OLD BATTERIES PROMPTLY AND PROPERLY. DO
NOT BURN OR BURY THEM.

TO INSTALL BATTERIES:

1. Open the battery compartment cover (located on the

back of the remote).

2. Place the “AA” batteries in the compartment and match

the

and

– polarity symbols inside.

3. Replace the cover.

NOTE: WHEN THE BATTERY VOLTAGE IS LOW, THE SOURCE KEY LED WILL
BLINK 5 TIMES AFTER A KEYPRESS.