Panasonic DMP-BDT110 - Manual (Page 37)

Re
fe
re
n
ce
37
VQT3B58
Messages
The following messages or service numbers appear on the
television or unit’s display when something unusual is
detected during startup and use.
Cannot play.
¾ You inserted an incompatible disc (Discs recorded in
PAL video, etc.).
Cannot display on this unit.
¾ You tried to play a non-compatible image.
¾ Confirm “SD” on the unit’s display is not displayed and
re-insert the card.
No disc is inserted.
¾ The disc may be upside down.
$ This operation is not available.
¾ Some operations are unsupported by the unit. For
example;
– BD-Video: During playback, reverse slow-motion or
reverse frame-by-frame is not possible.
IP address is not set.
¾ The “IP Address” in “IP Address/DNS Settings” is “---.
---. ---. ---”. Set the “IP Address”, “Subnet Mask”, and
“Default Gateway”. (Select the automatic address
acquisition if necessary.)
The current settings only offer minimal
wireless access point security and low
performance. It is recommended to change it
for better security.
¾ Authentication type for the Wireless LAN is set to “Open
system”, or the encryption type is set to “No encryption”.
It is recommended to encrypt for safety reasons. For
details, refer to the instructions of the Wireless router
being used. Encryption is required when playing back
video, etc., from DLNA compatible devices.
F99
¾ The unit fails to operate properly. Press [POWER Í/I]
on the main unit for 3 seconds to switch the unit to
standby, then switch back on.
HDMI ONLY
¾ Some BD-Video discs can only be output with HDMI.
NET
¾ While connecting to a network.
No PLAY
¾ There is a viewing restriction on a BD-Video or
DVD-Video. (> 29)
No READ
¾ The media is dirty or badly scratched. The unit cannot
play.
PLEASE WAIT
¾ The unit is carrying out an internal process. This is not a
malfunction. You cannot operate the unit while “PLEASE
WAIT” is displayed.
REMOVE
¾ The USB device is drawing too much power. Remove
the USB device.
SET 
(“  ” stands for a number.)
¾
The remote control and main unit are using different
codes. Change the code on the remote control.
Press and hold [OK] and the
indicated number button at the
same time for more than
5 seconds.
U59
¾ The unit is hot.
The unit switches to standby for safety reasons. Wait for
about 30 minutes until the message disappears.
Select a position with good ventilation when installing
the unit. Do not block the ventilation hole on the side of
the unit.
U72
U73
¾ The HDMI connection is not working properly.
– Turn the unit and TV off.
– Disconnect the HDMI cable between the player and
the TV.
H or F
(“  ” stands for a number.)
¾
There is something unusual.
¾ Check the unit using the troubleshooting guide. If the
service number does not disappear, do the following.
1 Disconnect the plug from the AC outlet, wait a few
seconds, then reconnect it.
2 Press [POWER Í/I] to turn the power on.
If the service number does not disappear despite doing the
above, request service from the dealer. Inform the dealer of
the service number when requesting service.
START
¾ The system is being restarted during the firmware
update. Please do not turn off the unit.
UPD/
(“  ” stands for a number.)
¾
The firmware is being updated.
Please do not turn off the unit.
FINISH
¾ The firmware update is complete.
On the television
On the unit’s display
VQT3B58~Body_eng.fm 37 ページ ２０１０年１２月１０日 金曜日 午後９時３０分