Philips VR752/07 - Manual (Page 18)

18 EN
7. 7. When all inputs are correct, press .
The programming information is stored in a
Timer block.
8. 8. Insert a cassette with an intact security tab
(unprotected).
9. 9. Switch off with . The pro-
grammed recording will only function when
the video recorder is switched off with
.
Programming a recording
(without the VIDEO Plus+ system)
1. 1. Switch the TV on. If applicable, select the pro-
gramme number for the video recorder opera-
tion.
2. 2. Press . The main menu will appear.
3. 3. Select 'TIMER' with or .
Then press .
4. 4. Select 'ONCE', 'DAILY' or 'WEEKLY' recording
with or . Then
press
.
5. 5. Select the desired Timer block with .
6. 6. Enter the Start time (START), End time
(STOP), Programme number (PROG.), PDC
information and the Date (DATE) with
.
7. 7. When all inputs are correct, press
. The programming information
is stored in a TIMER block.
8. 8. Insert a cassette with an intact security tab
(unprotected).
9. 9. Switch off with .
The programmed recording will only function
when the video recorder is switched off with
. STANDBY/ON y y
STANDBY/ON y y
STATUS/EXIT
0..9
0..9
FWD 1 - B
STOP C-L PLAY B-K
FWD 1- B
STOP C-L PLAY B-K
MENU
STANDBY/ON y y
STANDBY/ON y y
STATUS/EXIT
SELECT K L CHOOSE B
→ ONCE
DAILY
WEEKLY
TIMER LIST
END=EXIT
Programme numbers of the 'AV1', 'AV2' scart
socket and 'AV3' (
FRONT A/V CONNECTORS )
You can also programme recordings from exter-
nal sources via scart socket AV1(TV), AV2
(DECODER) or AV3 (FRONT A/V CONNEC-
TORS). Select programme number 'AV1' with
0.0.1, 'AV2' with 0.0.2 or 'AV3' with 0.0.3.
'- -' appears at PROG. .
• The programme number of the TV channel
has not yet been assigned to the PlusCode
programming number. Using the number but-
tons
on the remote control, select the
corresponding programme number (name) of
the TV channel.
The following message appears on the
screen: 'ERROR'
• The entered PlusCode programming number
is incorrect. Correct your input or end with
.
• Check the time/date (see chapter 'Installing
your video', section 'Setting the clock').
• A daily recording was entered for the wrong
day. Daily programming can only be used for
recordings to be made from Monday to Friday.
Switching on 'PDC'
• Select 'PDC' using
.
Press '1' to switch off 'PDC' or press '2' to
switch on 'PDC'.
CLEAR FWD 1 - B
STATUS/EXIT
0..9
Selecting ONCE/DAILY/WEEKLY recordings
'ONCE': Recording once
'DAILY': Repeated daily recordings
(Monday to Friday)
'WEEKLY': Repeated weekly recordings
(every week on the same day)
Error message: 'FULL'
•
I f this error message appears after you select
'ONCE', 'DAILY' or 'WEEKLY' on TIMER menu
and press
, then all TIMER blocks
are already programmed. No more recordings
can be programmed. If you want to clear or
check a programmed recording (TIMER block),
select the programme number on TIMER LIST
menu and press
. CLEAR
FWD 1- B
The following message appears on the
screen: 'TIMER NOT COMPLETED'
• The channel is wrong.
HG491/495BD(EN).qx3 03.12.19 9:54 PM Page 18