Pioneer BONUSVIEW BDP-LX91 - Manual (Page 66)

07
66
En
• Picture is stretched.
• Picture is cropped.
• Aspect ratio cannot be
switched.
Is the TV’s aspect ratio properly set? Read the TV’s operating instructions and set the TV’s aspect
ratio properly.
Is TV Aspect Ratio properly set? Set TV Aspect Ratio properly (page 43).
Is 4:3 Video Out properly set? Set 4:3 Video Out properly (page 43).
Is DVD 16:9 Video Out properly set? Set DVD 16:9 Video Out properly (page 43).
When video signals with a resolution of 1080/50i, 1080/50p, 720/
50p, 1080/24p, 1080/60i, 1080/60p or 720/60p are being output
from the
HDMI OUT terminals or the COMPONENT VIDEO
output terminals, they may be output with an aspect ratio of
16:9 even if
TV Aspect Ratio is set to 4:3 (Standard) (page 43).
Is Anamorphic Zoom set to On? Set Anamorphic Zoom to Off (page 51).
Picture is interrupted. The picture may be interrupted when the resolution of the
recorded video signal switches. Press
OUTPUT RESOLUTION
to select a setting other than Auto, 1080/24p or Source Direct
(page 24).
Sound and picture are not
synchronized. Is Output Terminal properly set? Set Output Terminal properly (pages 20 and 43).
Is Lip Sync properly set? Adjust the amount of audio delay with the Lip Sync setting
(page 41).
• No sound is output.
• Sound is not output
properly.
Is the disc played back in slow motion?
Is the disc played back in fast forward or fast reverse?
No sound is output during slow motion play and forward and
reverse scanning.
Are the audio cables properly connected? • Connect the cable properly according to the connected
devices (page 14).
• Insert the cable firmly and all the way in.
Is the audio cable damaged? If the cable is damaged, replace it with a new one.
Are the connected components (AV receiver or amplifier, etc.)
properly set? Read the operating instructions of the connected components
and check the volume, input, speaker settings, etc.
Is Output Terminal properly set? When ANALOG AUDIO is selected at Output Terminal, no
audio signals are output from the HDMI OUT or DIGITAL OUT
terminals (page 43).
Is the output video resolution properly set? Use OUTPUT RESOLUTION to switch to the resolution at
which the video and audio signals are output (page 24).
Is the AV receiver or amplifier, etc., connected to the AUDIO
OUT (7.1 ch) terminals?
To listen to 2-channel analog audio, connect to FRONT (L/R) of
the AUDIO OUT (7.1 ch) terminals (page 13) and set Audio
Output Mode to 2 Channel (page 44).
Are the speakers properly set? When the AV receiver or amplifier, etc., is connected to the
AUDIO OUT (7.1 ch) terminals and Audio Output Mode is
set to
Multi-channel, set Speaker Setup properly (page 46).
Is Pure Audio set to Mode 1 or Mode 2? If set to Mode 1 or Mode 2, signals are only output from the
output terminal set at Output Terminal (page 52).
Is a DVI device connected? The sound will not be output from the HDMI OUT terminals if a
DVI device is connected. Connect the device to a DIGITAL OUT
terminals or the AUDIO OUT (7.1 ch) terminals (page 17).
Are you playing a DTS-CD? To output the sound of DTS-CDs from the HDMI OUT (SUB)
terminal, set HDMI Audio Out to PCM (page 44).
For some BDs, audio signals are only output from DIGITAL
OUT terminals or the HDMI OUT terminals.
Multi-channel sound is not
output. Is Output Terminal properly set? Linear PCM (2-channel) audio signals are output from output
terminals other than the one set at
Output Terminal under
Audio Out. Set Output Terminal properly (page 43).
Is the AV receiver or amplifier connected to the HDMI OUT
(SUB) terminal?
The HDMI OUT (SUB) terminal outputs linear PCM 2-channel
audio signals. Be sure to connect the AV receiver or amplifier
to the
HDMI OUT (MAIN) terminal.
Is the audio output of the connected AV receiver or amplifier,
etc., properly set? Read the operating instructions of the connected AV receiver
or amplifier and check the audio output settings of AV receiver
or amplifier.
Is multi-channel sound selected? Use the menu screen or AUDIO to switch the disc’s sound to
multi-channel.
Is the AV receiver or amplifier, etc., connected to the AUDIO
OUT (7.1 ch) terminals?
When the AV receiver or amplifier, etc., is connected to the
AUDIO OUT (7.1 ch) terminals, set Audio Output Mode to
Multi-channel (page 44). Also, set Speaker Setup properly
(page 46).
Problem Check Remedy