Panasonic DMP-BD35 User Manual

Page 30

RQT9248

TV screen and video (continued)

Page

Sound

HDMI connections

Video is not output in high
definition.

≥High definition video cannot be output through the VIDEO OUT terminal.

≥Confirm that the “HDMI Video Mode”, “HDMI Video Format”, and “Component Resolution” in

the Setup menu are set properly.

≥The video output resolution is restricted to “576p/480p” when DVD-Video discs and BD-Video discs

recorded at a rate of 50 field per second are output from the COMPONENT VIDEO OUT terminals.

—

Status messages do not appear.

≥Select “Automatic” in “On-Screen Messages” in the Setup menu.

The 4:3 aspect ratio picture
expands left and right.

Screen size is wrong.

≥Use the television to change the aspect. Refer to your television’s operating instructions.

≥When using a component video cable, set “Progressive” to “Video”. If the situation is not

restored after that, set “TV Aspect” to “4:3 Pan & Scan”.

—

23, 26

There is a lot of after-image
when playing video.

≥Turn “3D NR” or “Integrated NR” off if it is on.

There is no apparent change in
picture quality when adjusted
with the “Picture” menu in the
on-screen menu.

≥The effect is less perceivable with some types of video.

—

The masked-off area is masked
in gray.

≥If the “Screen Saver Function” in the Setup menu is set to “Off”, the masked-off area is

displayed in black.

Still pictures (JPEG) do not
playback normally.

≥The images that were edited on the PC, such as Progressive JPEG, etc., may not playback.

No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.

≥Check the connections and the “Digital Audio Output” settings. Check the input mode on the

amplifier/receiver if you have connected one.

≥Press [AUDIO] to select the audio.

≥Turn off “V. Surround” in the following cases.

– When using discs that do not have surround sound effects such as Karaoke discs.
– When playing bilingual broadcast programs.

≥The sound effects (Re-master, V. Surround, etc.) will not work when the bitstream signal is

output from the HDMI AV OUT terminal or the DIGITAL AUDIO OUT terminal.

6–8, 25

14
23

—

Cannot switch audio.

≥There are discs for which audio cannot be changed because of how the disc was created.

≥When connecting an amplifier/receiver using a optical digital audio cable or an HDMI cable,

you cannot switch the audio if “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” is set to
“Bitstream”. Set “Dolby D/Dolby D +/Dolby TrueHD” or “DTS/DTS-HD” to “PCM” or connect
using AUDIO OUT terminal.

—

7, 8, 25

The images from this unit do
not appear on the television.

Picture is distorted.

Jittering occurs.

≥Press [∫] and [1] (PLAY) simultaneously on the unit for more than 5 seconds to shift to more

compatible mode with HDMI equipment. However, Dolby Digital Plus, Dolby TrueHD, and
DTS-HD audio are not output in bitstream. To output the bitstream, select “Default Settings”
to restore the factory presets and make proper settings.

≥To output video from a device connected with an HDMI cable, set “HDMI Video Mode” to “On”

in the Setup menu.

≥Picture may not be seen when more than 4 devices are connected with HDMI cables.

Reduce the number of connected devices.

≥When “24p Output” is set to “On”, HDMI authentication takes place where 24p images switch

to other images, and a black screen is displayed.

≥When “24p Output” is set to “On”, jittering may occur while playing DVD-Video. In this case,

turn “24p Output” to “Off”.

—

The 4:3 aspect ratio picture
expands left and right.

Screen size is wrong.

≥Change “TV Aspect” type to “16:9”.

When playing DVD-Video using
progressive output, one part of
the picture momentarily
appears to be doubled up.

≥When you use the HDMI AV OUT terminal for video output, follow the steps below for setting.

1 Connect this unit to the TV with any cable except the HDMI cable.
2 When you connect with the Component Video cable, set “HDMI Video Mode” to “Off” and

“Component Resolution” to “576i/480i” in the Setup menu.

No sound.
Low volume.
Distorted sound.
Cannot hear the desired audio
type.

≥Audio may not be heard when more than 4 devices are connected with HDMI cables.

Reduce the number of connected devices.

≥The sound effects will not work when the bitstream signal is output from the HDMI AV OUT

terminal or the DIGITAL AUDIO OUT terminal.

≥To output audio from a device connected with an HDMI cable, set “HDMI Audio Output” to

“On” in the Setup menu.

≥Depending on the connected equipment, the sound may be distorted if this unit is connected

with an HDMI cable.

≥When “BD-Video Secondary Audio” is set to “On”, Dolby Digital Plus, Dolby TrueHD, and

DTS-HD are converted to 48 kHz Dolby Digital or DTS Digital Surround and output. LPCM
7.1 channel audio is converted to 5.1 channel audio. In this case, set the “BD-Video
Secondary Audio” to “Off”.

—

DMP-BD35GT&GN-RQT9256_eng.book 30 ページ２００８年９月２４日　水曜日　午後５時５分