KORG BX-3 - Manual (Page 28)

Parameters
28
* (Pdl 1), (Pdl 2): These indicate that Pedal 1 or Pedal 2 are selected for the Global mode Group 1 “Prog Up Ctrl” or “Prog Down Ctrl” parameters. With these settings, the settings of
Global mode are used, and the settings you made here will be ignored. However if you select another value in Global mode, the display here will change from (Pdl 1) to Pedal 1 or
from (Pdl 2) to Pedal 2, and you will be able to operate the corresponding function from the pedal switch.
Rotor Up Transit (Rotor Up Transition) [0...99]
Adjusts the time over which the rotor rotation changes
from slow to fast.
Rotor Down Transit (Rotor Down Transition) [0...99]
Adjusts the time over which the rotor rotation changes
from fast to slow.
Fast Speed
Slow Speed
Fast
Up Transit Down Transit
Slow
Speed
Time
Rotor Stop Transit (Rotor Stop Transition) [0...99]
Adjusts the time over which the rotor rotation actually
comes to a stop after you stop the rotation.
Rotor Strt Transit (Rotor Start Transition) [0...99]
Adjusts the time over which the rotor reaches the speci-
fied speed after it begins to rotate.
Slow or Fast Speed
Stop
Start Transit Stop Transit
Start
Speed
Time
When Rotary is on
Horn Mic Distance [0...99]
Adjusts the distance between the horn and the mic.
Horn Mic Spread [0...99]
Adjusts the distance between the “simulated mics” to
increase the stereo field.
Rotor Mic Distance [0...99]
Adjusts the distance between the rotor and the mic.
Rotor Mic Spread [0...99]
Adjusts the distance between the “simulated mics” to
increase the stereo field.
Mic Distance Mic Distance
Mic Spread
Horn
Rotor
○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○ ○
Group 7: Controller
Split Point (Keyboard Split Point) [C2...C7]
Specifies the split point used when you split the key-
board. The key you specify here will be the highest note
of the lower keyboard.
Split Upper Octave (Upper Octave Shift) [-2, -1, 0]
Lowers the pitch of the upper keyboard (when split is
used) in steps of one octave.
Split Lower Octave (Lower Octave Shift) [0, 1, 2]
Raises the pitch of the lower keyboard (when split is
used) in steps of one octave.
Hold Uppr Ctrl (Hold Upper Controller)
[Off, Pedal 1/(Pdl 1)*, Pedal 2/(Pdl 2)*]
Pedal 1 : A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will switch Hold on/off
for notes played on the upper keyboard.
Pedal 2
: A pedal switch etc. connected to the ASSIGN-
ABLE PEDAL/SW 2 jack will perform the above opera-
tion.
Off
: No function.
Hold Lowr Ctrl (Hold Lower Controller)
[Off, Pedal 1/(Pdl 1)*, Pedal 2/(Pdl 2)*]
Pedal 1 : A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will switch Hold on/off
for notes played on the lower keyboard.
Pedal 2
: A pedal switch etc. connected to the ASSIGN-
ABLE PEDAL/SW 2 jack will perform the above opera-
tion.
Off
: No function.
Wheel Brk Ctrl (Wheel Brake Controller)
[Off, Pedal 1/(Pdl1)*, Pedal 2/(Pdl 2)*]
This is displayed in Normal Edit mode.
Pedal 1
: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 1 jack will switch the “Wheel
Brake” parameter (Global mode Group 7) on/off.
Pedal 2
: A pedal switch etc. connected to the rear panel
ASSIGNABLE PEDAL/SW 2 jack will perform the above
operation.
Off
: No function.
Wheel Brk Pedal (Wheel Brake Pedal Mode)
[Alter, Momnt]
Select the on/off operation of the pedal switch etc.
connected to the rear panel ASSIGNABLE PEDAL/SW 1
or 2 jack.
Alter
: The pitch will begin falling once you press the
pedal switch. When you press it once again, the pitch will
gradually rise to the normal state.
Momnt
: The pitch will gradually fall as long as you
continue pressing the pedal switch. When you release the
pedal switch, the pitch will gradually rise to the normal
state.