Kenwood KRF-V4550D - Manual (Page 17)

17
Operations
Jot down the distance to each of the speakers.
Distance to front speakers: ____ feet (meters)
Distance to center speaker: ____ feet (meters)
Distance to surround speakers: ____ feet (meters)
2 Use the MULTI CONTROL to select the distance to the front
speakers.
Input level adjustment (analog sources only)
If the input level of an analog source signal is too high, adjust the input
level.
1 Use the INPUT SELECTOR knob to select the source who’s
input level you want to adjust.
• You can store a separate input level for each input source. If the
MONITOR function is on, you can store an input level for when
MONITOR is on independently of the input levels for the input
sources.
2 Press the SOUND key several times until the "INPUT" indica-
tion appears.
3 Use the MULTI CONTROL to adjust the input level.
• The adjustment mode is displayed for approximately eight sec-
onds.
• The input level may be adjusted to any one of three settings: 0,
-3, and -6. (The initial setting is 0.)
4 Press the SOUND key to return to the input indication.
Preparing for playback
Normal playback
Some preparatory steps are needed before starting playback.
Turning on the receiver
1 Turn on the power to the related components.
2 Turn on the power to this receiver by pressing POWER and ON/
STANDBY keys.
Selecting MD/TAPE
Select the source name corresponding to the component connected to
the MD/TAPE jacks. The initial factory setting is "TAPE". To change the
source name associated with the MD/TAPE jacks to "MD," follow the
steps below:
1 Use the INPUT SELECTOR knob to select "TAPE".
2 Hold down the AUTO key for more than 2 seconds.
• The source indication changes to "MD".
• To return to the original indication, repeat the above procedure.
• You also will need to change the name input to the remote control
to "MD".
Selecting the input mode
If you have selected a component connected to the CD/DVD, DVD/
6ch or VIDEO2/MONITOR jacks, make sure that the input mode
setting is correct for the type of audio signal to be used.
7
5 Setup is complete when the input indication reappears.
Display when all speakers have been selected.
• The speakers you selected appear on the display. Confirm that all
the speakers have been correctly selected.
The speaker indicator to be adjusted blinks.
Indication in feet Indication in meters
1 Measure the distance from the listening position to each of the
speakers.
• The allowable setting range is 1 to 30 feet (0.3 to 9.0 m),
adjustable in 1 foot (0.3 m) increments.
3 Press the SET UP key.
4 Repeat steps 2 and 3 to input the distance for each of the
speakers.
LFE
C
S RS LS
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
L SP R
SW
SW STEREO
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND AUTO
LFE
C
S RS LS
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
L SP R
STEREO
SW STEREO
FM
AM
MHz
kHz
PRO LOGIC
3
DOWN MIX
DIGITAL
S.DIRECT
MONITOR
DSP
MEMO
ST.
TUNED
AUTO SOUND AUTO
LFE
C
S RS LS
TI.VOL B
CLIP MUTE
RDS EON PTY
TP TA NEWS
L SP R
STEREO
AUTO
INPUT MODE
POWER
ON/STANDBY
INPUT SELECTOR
SPEAKER
MUTE
LFE
C
S RS LS
TI.VOL
CLIP MUTE
RDS EON PTY
TP TA NEWS
L SP A R
SW
B
The speaker indicator lights.
Press the SPEAKER key to switch the speakers on and off.
Preparing for surround sound
4
Input the distance to the speakers.
*4967/01-/EN 3/19/01, 6:34 PM 17