Sunfire Theater Grand Receiver TGR-401-230 - Manual (Page 46)

User's Manual
46
CHAPTER 5
The supplied AM and FM antennas
must be connected to the TGR-401
antenna terminals, or no stations will
be tuned.
The internal AM and FM tuners are
selected either by pressing Input and
rotating the manual selector on the
front panel, or by touching the AM or
FM buttons in the remote’s TGR-401
page 2. The front panel display will
change to show the frequency of the
last station you were listening to.
The FM tuner can tune stations
from 87.5 MHz to 108.0 MHz in 0.2
MHz steps (.05 MHz steps for some
international models). The AM tuner
range is 530 kHz to 1710 kHz in 10
kHz steps (531 kHz to 1710 kHz in
9 kHz steps for some international
models).
1. Press the remote's MAIN button
to make sure the display is on the
main display menu.
2. Press the TG401 de-
vice button to set the
remote to operate
your TGR-401. The
display changes to
show the TGR-401
input selections.
3. Press PAGE to
reach page 2. This
allows selection of
the SIRIUS tuner,
FM and AM tuner,
TNMOD and SCAN.
TNMOD lets you use
the number keys
either to enter the station frequen-
cy directly, or to enter the preset
station number. TNMOD is also
available in Zone 2.
SCAN lets you scan up to the next
tunable station. It will remain there
for 5 seconds before scanning
up to the next station. Press the
Navigation SEL button to select a
the currently-playing station.
FM and AM Tuner Operation
4. Various remote buttons also oper-
ate the AM and FM tuner:
• NAVIGATION KEYPAD - multifunc-
tional for setup menu navigation
and AM/FM tuning.
• NAV UP - Tunes up one frequency
step at a time. If you hold it down,
it will scan up to the next station.
• NAV DOWN - Tunes down one fre-
quency step at a time. If you hold it
down, it will scan down to the next
available station.
• NAV SELECT - Select a station.
• INFO - Show the current station
frequency and preset number, or
the listening mode.
• MENU - Enter the OSD Setup
menu where FM and AM presets
can be configured.
• CH UP/DOWN - Tunes up and
down through preset list. The list is
created in the preset menu within
the setup menu.
• NUMBER KEYS - These allow you
to enter the actual frequency of
the station directly. If you press TN-
MOD, you can enter station preset
numbers instead.
5. To operate FM/AM
in Zone 2, select the
Zone 2 button, then
Zone 2's first page
will show the FM/AM
input selectors.
Changing Modes
1. Press the INFO button until the
front panel display shows the cur-
rent surround mode. Then use the
mode buttons to select a mode.
Saving Presets
The OSD preset menu is used to
enter the preset number and frequen-
cy of your favorite radio stations.
1. In the AM/FM preset menu,
press the remote's center navi-
gation select (SEL) to choose
AM or FM, or reset a preset to
NONE.
2. Use the navigation up or down
to move to the preset number,
for example, preset 01.
3 1
6 4
9 7
2
EXIT
ENT +10
CH VOL
MUTE PREV
CH
MENU
INFO
GUIDE
MAIN
FAV
OFF ON
PAGE
SEL
5
8
0
MAIN
PAGE
CH UP/DOWN
INFO
NAV DOWN
NAV UP
MENU
NAV SELECT
TGR401
ZONE 2
NUMBER KEYS
PRESETS
AM/FM
SIRIUS
MAIN MENU
TRIMS
TONE CONTROLS
MODES
PRESETS
SETUP
SIRIUS
PRESETS
CHANNEL CHOICES
01 1 1–223/NONE
02 223
03 NONE
04 NONE
05 NONE
.
40 NONE
AM/FM
PRESETS
FREQ CHOICES
01 FM 107.50 AM/FM, FREQ/NONE
02 FM 98.30
03 FM 99.90
04 AM 1230
05 AM 610
06 NONE
.
40 NONE
MODE MODE