Sunfire Theater Grand Receiver TGR-401-230 - Manual (Page 39)

User's Manual
39
CHAPTER 5
Manual Setup
The following On Screen Display
(OSD) menus are used to enter and
make three main adjustments:
• Speaker Size
• Level Calibration
• Speaker Distance
This setup needs to be done
when you use your system for
the first time, or if you change
anything such as the amplifiers or
speakers, or the speaker posi-
tion. The calibration is also a good
way to check that your system is
working correctly. These adjust-
ments are made using the OSD
as follows:
1. With the remote control set to
operate the TGR-401, press the
MENU button to bring up the
MAIN Menu of the OSD on your
TV.
2. Use the navigation pad left, right,
up and down buttons to navigate
through the menus in the next
steps.
NOTE: Quit the OSD at any time
by pressing the nearby EXIT but-
ton. Any changes will be saved.
There is no need to navigate back
through previous pages, unless
you want to make more changes.
The TGR-401 front panel display
shows the same messages as the
OSD.
3. In the MAIN Menu, select SETUP,
and from there select the SPEAK-
ERS Menu.
4. In the SPEAKERS Menu, select
the SPEAKER SIZE Menu. Use
the navigation pad to set the size
of each speaker to Large, or set to
OFF for those speakers which are
not present. For speakers with the
bass redirected to the subwoofer,
set to 90 Hz. This is a good start-
ing point. Return to the SPEAK-
ERS Menu when you are finished.
5. In the SPEAKERS Menu, select
the DISTANCE Menu. Enter how
far each speaker is from your
listening position. (Measure the
distance with a tape measure.)
6. Turn down the main volume
before you begin the level cali-
bration, or it can be loud. In the
SPEAKERS Menu, select the
LEVEL CALIBRATION Menu to
adjust the output of each speaker.
A test noise plays in each se-
lected speaker. Use the remote's
volume buttons to increase the
starting volume to a comfortable
level, then use the remote's navi-
gation buttons to adjust the level
of each speaker in turn, until they
are all playing at the same level.
Return to the SPEAKERS Menu
when you are finished.
7. Press the remote’s EXIT button to
quit the OSD. Now the TGR-401
is setup correctly and ready for
action.
LEVEL CALIBRATION DB CHOICES
FRONT LEFT 0 (-20 TO +20 IN 0.5 DB STEPS)
CENTER 0
FRONT RIGHT 0
SURR RIGHT 0
BACK SURR R 0
BACK SURR L 0
SURR LEFT 0
SUB 0
SPEAKERS
AUTO SETUP
SPEAKER SIZE
DISTANCE
LEVEL CALIBRATION
EQ
BINDING POSTS
DISTANCE FT CHOICES
FRONT LEFT 0.0 0.0 - 25.0 FEET (6 INCH STEPS), 0 - 7.5
METERS (0.15 METER STEPS)
CENTER 0.0
FRONT RIGHT 0.0
SURR RIGHT 0.0
BACK SURR R 0.0
BACK SURR L 0.0
SURR LEFT 0.0
SUB 0.0
UNITS FEET FEET/ METERS
SPEAKER SIZE CHOICES
FRONT 90HZ LARGE,40,45,50,55,60,65,...150
CENTER 90HZ OFF, LARGE,40,45,50,55,60,65,...150
SURROUND 90HZ OFF, LARGE,40,45,50,55,60,65,...150
BACK SURR 90HZ OFF, LARGE,40,45,50,55,60,65,...150
NUM BACK
SPKRS
2 N/A,1,2
SUBWOOFER 90HZ OFF, 40,45,50,55,60,65,...150
SUBWOOFER
MODE
NORM NORMAL, ENHANCED
SETUP
INPUTS
SPEAKERS
VIDEO
MAIN ZONE
ZONE 2
CONTROL
DIGITAL OUT DN MIX/THRU
DIMMER LOW/MEDIUM/HIGH
MAIN MENU
TRIMS
TONE CONTROLS
MODES
PRESETS
SETUP