JVC GM-X50E - Manual (Page 11)

10
Precautions
• Before making connections, turn off all the equipment.
• Use a cord whose plugs are correctly matching for the terminals on this Monitor and the equipment.
• Plugs should be firmly inserted; poor connection could cause noise.
• To unplug a cord, be sure to grasp its plug and pull it out.
• Connect the power cord after having finished all other connections.
• Refer also to the user manual of each piece of equipment.
Available Signals
Video signals
The following signals can be input to this Monitor:
• VIDEO A and VIDEO B terminals accept — PAL, PAL60, NTSC, NTSC 4.43, and SECAM signals.
• COMPONENT/RGB B terminals accept — 480i, 576i, 480p, 576p, 720/60p, 720/50p, 1080/60i (1035/60i), and 1080/50i signals.
(You need to set “COMPO./RGB B” to “COMPO.” on the menu (see page 20).
Computer signals (Preset)
This Monitor has 27 preset video modes for the most popular industrial standard, and the signals of the following image
resolutions can be input to the RGB input terminals.
1 PC98 640 400 24.8 56.4 Non-interlace
2 VGA400-70 640 400 31.5 70.1 Non-interlace
3 VGA480-60 640 480 31.5 59.9 Non-interlace
4 WVGA-60 852 480 31.7 60.3 Non-interlace
5 VGA480-72 640 480 37.9 72.8 Non-interlace
6 VGA480-75 640 480 37.5 75.0 Non-interlace
7 SVGA-56 800 600 35.2 56.3 Non-interlace
8 SVGA-60 800 600 37.9 60.3 Non-interlace
9 SVGA-72 800 600 48.1 72.2 Non-interlace
10 SVGA-75 800 600 46.9 75.0 Non-interlace
11 XGA-60 1024 768 48.4 60.0 Non-interlace
12 WXGA-60 1366 768 48.4 60.0 Non-interlace
13 XGA-70 1024 768 56.5 70.1 Non-interlace
14 XGA-75 1024 768 60.0 75.0 Non-interlace
15 XGA-85 1024 768 68.7 85.0 Non-interlace
16 XGA+-75 1152 864 67.5 75.0 Non-interlace
17 SXGA-60 1280 1024 64.0 60.0 Non-interlace
18 SXGA-75 1280 1024 80.0 75.0 Non-interlace
19 UXGA-60 1600 1200 75.0 60.0 Non-interlace
20 UXGA-65 1600 1200 81.3 65.0 Non-interlace
21 UXGA-70 1600 1200 87.5 70.0 Non-interlace
22 MAC13” 640 480 35.0 66.7 Non-interlace
23 MAC16” 832 624 49.7 74.6 Non-interlace
24 MAC19” 1024 768 60.2 74.9 Non-interlace
25 MAC21” 1152 870 68.7 75.1 Non-interlace
26 RGB15K-60 — — 15.7 59.9 Interlace
27 RGB15K-50 — — 15.6 50.0 Interlace
Notes:
• When a signal other than listed above is input, a part of the screen may become void or an unnecessary picture may appear.
• Signals, though they are within the acceptable range of frequencies, may not be displayed normally, depending on the signal
type.
• Depending on the connected equipment, the Monitor may not be compatible with composite sync (Cs) or G on sync signals.
• When a preset mode signal is input, the vertical frequency displayed on the screen will have an “*” shown at its right top
position.
• When the No. 3 and No. 11 signals are input, set “SAMPLING MODE” to “STD” on the menu (see page 25).
• When the No. 4 and No. 12 signals are input, make the following settings:
– Set “SAMPLING MODE” to “WIDE” on the menu (see page 25).
– Change the aspect ratio to “FULL” (see pages 15 and 19).
• When No. 16 to No. 21 and No. 25 signals are input, thin lines may become obscure for their signal frequencies are higher
than the screen resolution. Using the RGB A input terminals makes the lines clearer than using the RGB B input terminals.
• The adjustment of the screen size and position is the setting common to the No. 14 and No. 24 signals. If you use both signals
by switching them, the adjustment of either signal may not be proper.
Connections
Screen resolution
Horizontal Vertical
Horizontal
Frequency (kHz)
Vertical
Frequency (Hz)
Signal name Scan system No.
04-13_GM_X50EB.p65 04.7.13, 11:46 PM 10