JVC LVT1321-010C - Manual (Page 35)

33
On the front panel:
Before you start, remember...
There is a time limit in doing the following steps. If the setting is
canceled before you finish, start from step
2 again.
1
Select and play any source other than DVD
MULTI.
• Make sure you have selected the input mode (analog or
digital) correctly.
2
Press SURROUND.
MULTI JOG now works for selecting Surround/DSP modes.
3
Turn MULTI JOG to select the Surround/DSP
mode you want.
Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital
multi-channel software:
* 1 “AUTO SURROUND” is the initial setting.
* 2 Available Surround modes vary depending on the speaker
settings and the incoming signals. For details, see page
32.
* 3 If an incoming signal is a multi-channel (more than 2
channel) digital signal, “MONO FILM” is not available.
* 4 If “SURROUND SPK” is set to “
<
NO
>
,” “ALL CH STEREO”
is not available.
To cancel Surround/DSP modes
Turn MULTI JOG so that “SURROUND OFF” appears on the
display.
When you select “AUTO SURROUND”
You can enjoy the Surround mode easily.
• For details about the Surround modes, see page 32.
• When “AUTO SURROUND” is activated, the AUTO SURR indicator
lights up on the display.
How does “AUTO SURROUND” work?
• If a multi-channel signal comes in, an appropriate Surround
mode will be selected automatically.
• If a Dolby Digital 2-channel signal with surround signal comes
in, “PLIIx MOVIE” or “PLII MOVIE” will be selected.
• If a Dolby Digital 2-channel signal without surround signal
comes in, “SURROUND OFF (stereo)” will be selected.
• If a Linear PCM signal comes in, “SURROUND OFF (stereo)”
will be selected.
NOTE
“AUTO SURROUND” does not take effect in the following cases:
– While playing an analog source,
– While selecting one of the fixed digital decode mode—“DOLBY
DIGITAL” or “DTS” (see page 15).
Activating the Surround/DSP modes
Available Surround/DSP modes vary depending on the speaker
settings and the incoming signals. For details, see page 32.
Activating one of the Surround/DSP modes automatically
recalls the memorized settings and adjustments.
• To adjust the speaker output level, see page 24.
• When activating one of the Surround/DSP modes, you
can adjust CENTER TONE. (see page 26)
• When activating one of the Surround/DSP modes
(except Pro Logic IIx Music, Pro Logic II Music, NEO:6
Music, and ALL CH STEREO), you can adjust CENTER
ALIGN. (see page 26)
• When activating NEO:6 MUSIC, you can adjust CENTER
GAIN. (see page 26)
• When activating the DSP mode (except All Channel
Stereo mode), you can adjust the following settings:
EFFECT (see page 25)
LIVENESS (see page 25)
ROOM SIZE (see page 25)
• When activating “PLIIx MUSIC” and “PLII MUSIC”, you
can adjust the following settings:
CENTER WIDTH (see page 26)
DIMENSION (see page 26)
PANORAMA (see page 25)
Selecting the Surround/DSP modes
From the remote control:
1
Select and play any source other than DVD
MULTI.
• Make sure you have selected the input mode (analog or
digital) correctly.
2
Press SURROUND repeatedly to select the
Surround/DSP mode you want.
Ex.: When “DOLBY DIGITAL” is selected for Dolby Digital
multi-channel software:
* 1 “AUTO SURROUND” is the initial setting.
* 2 Available Surround modes vary depending on the speaker
settings and the incoming signals. For details, see page
32.
* 3 If an incoming signal is a multi-channel (more than 2
channel) digital signal, “MONO FILM” is not available.
* 4 If “SURROUND SPK” is set to “
<
NO
>
,” “ALL CH STEREO”
is not available.
To cancel Surround/DSP modes
Press SURROUND repeatedly so that “SURROUND OFF”
appears on the display.
1
2
1,3 2
L
LS RS
S.WFR LFE
C R
DIGITAL
DIGITAL AUTO
SURROUND OFF (Back to the beginning)
Surround modes * 2 AUTO SURROUND * 1
HALL1 HALL2 LIVE CLUB DANCE CLUB
PAVILION THEATER1 THEATER2
MONO FILM * 3 ALL CH STEREO * 4
L
LS RS
S.WFR LFE
C R
DIGITAL
DIGITAL AUTO
SURROUND OFF (Back to the beginning)
Surround modes * 2 AUTO SURROUND * 1
HALL1 HALL2 LIVE CLUB DANCE CLUB
PAVILION THEATER1 THEATER2
MONO FILM * 3 ALL CH STEREO * 4
29-33RX-D301S[UJ]_f.p65 05.5.25, 5:34 PM 33