JVC HR-XV48EK - Manual (Page 20)

Filename [XV48EK_07S-VHS.fm]
Masterpage:Left+
Page 20 November 18, 2004 10:44 pm
OPERATIONS ON VHS DECK (cont.)
20
Instant ReView
Simply by pressing a single button, the unit power comes on,
rewinds, and begins playback of the last timer-recorded
programme. If you have several programmes recorded, you can
easily access any of them.
NOTE:
Before starting, make sure that the unit is off and that the Timer
mode is disengaged.
Activate Instant ReView.
Press . The unit power comes on and the unit
searches for the index code indicating the start of the last
timer-recorded programme. Once it’s found, playback
begins automatically.
● To watch the first of the 3 programmes, press three
times. The unit searches and begins playback automatically.
You can access a programme as far as 9 index codes away
from the current tape position.
Repeat Playback
Your unit can automatically play back the whole tape 100 times
repeatedly.
1 Start playback.
Press 4.
2 Activate Repeat Playback.
Press 4 and hold for over 5 seconds, then release.
● The Play indicator ($) on the front display panel blinks slowly.
● After playing back a tape 100 times, the unit stops
automatically.
3 Stop Repeat Playback.
Press 8 at any time.
Pressing 4, 3, 5 or 9 also stops Repeat Playback.
Manual Tracking
Your unit is equipped with automatic tracking
control. During playback, you can override this
and adjust the tracking manually by pressing the
TRACKING +/– buttons.
1 Override automatic tracking.
During playback, press TRACKING + and – at the same
time.
2 Adjust the tracking manually.
Press TRACKING +/–.
● Press TRACKING + and – at the same time again to return to
automatic tracking.
NOTE:
When a new tape is inserted, the unit enters the automatic
tracking mode automatically.
Soundtrack Selection
Your unit is capable of recording three soundtracks (HI-FI L,
HI-FI R and NORM) and will play back the one you select.
During Playback
Pressing A.MONITOR changes the soundtrack as follows:
NOTES:
● “HIFI L j h R” should normally be selected. In this mode,
Hi-Fi stereo tapes are played back in stereo, and the normal
audio track is played back automatically for tapes with only
normal audio.
● For instructions on recording stereo and bilingual
programmes, refer to page 23.
● “O.S.D.” must be set to “ON” or the on-screen displays will
not appear. (
੬
pg. 53)
NTSC Playback
Your unit is equipped with NTSC circuitry that can play back
NTSC tapes.
1 Load a cassette.
Insert a cassette recorded in NTSC.
2 Start playback.
Press 4.
● “NTSC]PAL” appears on the screen for about 5 seconds.
NOTES:
● Some TVs shrink the picture vertically and place black bars at
the top and bottom of the screen. This is not a malfunction on
the part of either the unit or the TV.
● The picture may roll up and down. This can be corrected using
the V-HOLD control found on some TVs. (This cannot be
corrected if the TV does not have a V-HOLD control.)
● The counter and tape remaining time readings will be incorrect.
● During search, still, or frame-by-frame playback, the picture
will be distorted, and there may be a loss of colour.
● Depending on the type of TV, the top and bottom portions of
superimposed displays may be cut off during NTSC playback.
Slide to the
right.
Track
Use
On-screen display
HI FI
L j h R
For Hi-Fi stereo tapes
HI FI
L j
For main audio of Bilingual tapes
HI FI
h R
For sub audio of Bilingual tapes
NORM For audio-dubbed tapes
HI FI
NORM
For audio-dubbed tapes
XV48EK_01.book Page 20 Thursday, November 18, 2004 10:45 PM