JVC LVT0870-006A User Manual
Page 58
55
For CATV converter
Manufacturer
Codes
GENERAL INSTRUMENT
06, 07, 08, 09, 10, 11,
12, 13, 14, 29
HAMLIN/REGAL
01, 02, 03, 04, 05
JERROLD
06, 07, 08, 09, 10, 11,
12, 13, 14
OAK
15, 16, 17
PANASONIC
18, 19, 20
PIONEER
21, 22
SCIENTIFIC ATLANTA
23, 24, 25
TOCOM
26
ZENITH
27, 28
Manufacturers’ codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
To change the transmittable signals for
operating a CATV converter or DBS tuner
1. Press and hold CATV/DBS
.
2. Press CATV/DBS CONTROL.
“CALL” appears on the remote control display window.
3 Enter a manufacturer’s code using buttons 1–9,
and 0.
See the following lists to find the code.
4. Release CATV/DBS
.
The following buttons can be used for operating the CATV
converter and DBS tuner:
CATV/DBS
:Turn on and off the CATV converter
or DBS tuner.
CH +/–
:Change the channels.
1 – 10, 0, 100+ (+10)
:Select the channels.
The 10-key will function as the
ENTER button if your equipment
requires pressing ENTER after
selecting a channel number.
Note:
Refer also to the manual supplied with your CATV converter or
DBS tuner.
5. Try to operate your CATV converter or DBS
tuner by pressing CATV/DBS
.
When your CATV converter or DBS tuner turns on or off, you
have entered the correct code.
If there are more than one code listed for your brand of
CATV converter or DBS tuner, try each one until the correct
one is entered.
Note:
You cannot preset the signals for both the CATV converter and DBS
tuner at the same time.
To change the transmittable signals for
operating another manufacturer’s VCR
1. Press and hold VCR1
.
2. Press VCR1.
“CALL” appears on the remote control display window.
3. Enter manufacturer’s code using buttons 1–9,
and 0.
See the list on the next page to find the code.
4. Release VCR1
.
The following buttons can be used for operating the VCR:
VCR1
:Turn on and off the VCR.
After pressing VCR1, you can perform the following operations
on the VCR:
CH +/–
:Change the TV channels on the
VCR.
1 – 10, 0, 100+ (+10)
:Select the TV channels.
The 10-key will function as the
ENTER button if your VCR requires
pressing ENTER after selecting a
channel number.
3 PLAY
:Start playback.
REW
:Rewind a tape.
FF
:Fast wind a tape.
7 STOP
:Stop playing or recording.
8 PAUSE:
:Pause playing. To resume, press
3 PLAY.
REC PAUSE
:Enter recording pause by pressing
this button.
To start recording again, press this
button then
3 PLAY.
Note:
Refer also to the manual supplied with your VCR.
5. Try to operate your VCR by pressing VCR1
.
When your VCR turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of
VCR, try each one until the correct one is entered.
Manufacturer
Codes
JVC
56
*
, 57, 67
AMSTRAD
43, 44, 45, 46, 47, 48, 49
BLAUPUNKT
30
ECHOSTAR
50, 51, 67
GOLDSTAR
31
GRUNDIG
32, 33
HIRSHMANN
48, 52, 53, 54, 55
INSTRUMENT
68
ITT/NOKIA
34
KATHREIN
52, 58, 59, 60, 61, 62, 63
NEC
35, 36
ORBITECH
48
PHILIPS
37, 38
RCA
65
SAMSUNG
39, 40
SCHWAIGER
61, 64
SIEMENS
41, 42
SONY
66
TECHNISAT
48
For DBS tuner
*Initial setting
EN49-60.RX-8020V[A]_f
02.5.21, 10:30 AM
55