JVC LVT0870-006A - Manual (Page 57)

54
Operating Other Manufacturers’ Video Equipment
To change the transmittable signals for
operating another manufacturer’s TV
1. Press and hold TV .
2. Press TV/DBS.
“CALL” appears on the remote control display window.
3. Enter a manufacturer’s code using buttons 1–9,
and 0.
See the list below to find the code.
4. Release TV .
The following buttons can be used for operating the TV:
TV :Turn on and off the TV.
TV VOL +/– :Adjust the volume.
TV/VIDEO :Set the input mode (either TV
or VIDEO).
After pressing TV/DBS, you can perform the following
operations on the TV:
CH +/– :Change the channels.
1 – 10, 0, 100+ (+10) :Select the channels.
The 10-key will function as the
ENTER button if your TV requires
pressing ENTER after selecting a
channel number.
Notes:
• Refer also to the manual supplied with your TV.
• All the functions listed above may not be assigned to the
buttons for some TVs.
• If you cannot change the channels of some TVs by pressing
number buttons, press CH +/– for changing the channels.
5. Try to operate your TV by pressing TV .
When your TV turns on or off, you have entered the correct
code.
If there are more than one code listed for your brand of TV,
try each one until the correct one is entered.
MENU
+
− +
− +
−
2 3 1
5 6 4
8 9 7/P
0 +10 10
BOOST ∗ FRONT•L
MENU
ENTER
∗ FRONT•R
BASS
DIMMER
TEST ∗ CENTER ∗ SUBWFR
∗ DIGITAL EQ ∗ SBACK•L ∗ SBACK•R
∗ SURR•L ∗ SURR•R
MUTING
CH/ ∗ LEVEL TV VOL
PLAY
STOP
/REW
DOWN – TUNING – UP
FF/
EXIT
VOLUME
CATV/DBS
CONTROL
TV/VIDEO
REC
PAUSE
SLEEP
PAUSE
SET
RETURN FM MODE 100+
CONTROL
RM-SRX8020J REMOTE CONTROL
CATV/DBS VCR1 TV AUDIO
DSP
OFF
DVD MULTI DVD
USB
CD
CDR
TAPE/MD
TV/DBS VIDEO PHONO
FM/AM
VCR1 VCR2
SURROUND SURR/DSP ANALOG/DIGITAL
A/V CONTROL RECEIVER
INPUT
DIRECT
ANALOG
TEXT
DISPLAY
SOUND
Note:
When you press one of the source selecting buttons, the
operation mode appears on the display window. For example,
the above illustration shows the remote control now works for
TV operation.
This remote control supplied with the receiver can transmit control
signals for other manufacturers’ TVs, CATV converters, DBS
tuners, VCRs and DVD players. By changing the transmittable
signals from preset ones to the other manufacturers’, you can
operate the other manufacturers’ components using this remote
control.
When operating the other manufacturers’ components, refer also to
the manuals supplied with them. To operate these components with
the remote control, first you need to set the manufacturers’ codes for
each TV, CATV converters, DBS tuners VCR and DVD players.
After replacing batteries for the remote control, you need to set the
manufactures’ codes again.
Buttons Indications
TV/DBS TV
CATV/DBS CONTROL CATV
VCR1 VCR1
DVD or DVD MULTI DVD
Manufacturers’ codes are subject to change without notice. If they
are changed, this remote control cannot operate the equipment.
Manufacturer Codes
JVC 00 * , 02, 13,
14, 47, 74
AKAI 01, 02
BLAUPUNKT 03, 04
FISHER 01, 05
GRUNDIG 03, 06, 07
HITACHI 08, 09, 10, 49
IRADDIO 02
ITT/NOKIA 11, 12
LOEWE 06, 15, 16
MAGNAVOX 08, 17, 49
METS 50, 51, 52, 53
MITSUBISHI 08, 18, 19, 20
MIVAR 21
NORDMENDE 22, 23
OKANO
15
PANASONIC 24, 25, 26, 27
76
PHILIPS 15, 17, 28, 75
QUELLE 52, 53, 54, 55,
56, 57, 58, 59,
60, 61, 62, 63,
64, 65, 66, 67
RCA/ 08, 24, 29, 30,
PROSCAN 31, 48
SABA 32, 33, 68, 69,
70
SAMSUNG 06, 08, 16, 34,
35, 49
SANYO 01, 05
SCHNEIDER 02, 15, 36
SHARP 37, 38, 77
SONY 39
TELEFUNKEN 40, 41, 42, 69
THOMSON
71, 72
TOSHIBA 37, 43, 44
ZENITH 45, 46
Manufacturer Codes
*Initial setting
EN49-60.RX-8020V[A]_f 02.5.21, 10:30 AM 54