beautypg.com

Maintenance instructions, Cleaning the bath, Repairs to the surface – Jacuzzi Comfort Plus Bath Series User Manual

Page 17: Purging the whirlpool system, Suction cover/strainer maintenance, Bath additives, Lamp

background image

ENGLISH

LIGHT BEZEL

SHELL

LOCKING NUT

LED LIGHT ASSEMBLY

NOTCH

GASKET

COVER STRAINER

SCREW

SUCTION
FITTING

SUCTION COVER/STRAINER ASSEMBLY

Cleaning the Bath

To clean your bath, simply use a mild, nonabrasive liquid deter-

gent solution. You can protect and restore the gloss to a dulled
acrylic surface by applying an acrylic polish or automotive paste wax.

Never use abrasive household cleaners on any Jacuzzi Whirl-

pool Bath

©

product.

Repairs to the Surface

Major scratches and gouges which penetrate the acrylic surface

will require refinishing. Contact your Jacuzzi Whirlpool Bath

©

dealer

for special instructions.

Purging the Whirlpool System

NOTE: THE WHIRLPOOL SYSTEM SHOULD BE PURGED AT

LEAST TWICE A MONTH
To remove accumulations of bath residue from the whirlpool system,
it is recommended that the whirlpool bath be purged at least twice a
month. For best results, however, we recommend that you purge your
whirlpool bath after each use using our exclusive two-part plumbing
system cleaner made specifically for whirlpool baths.

Systems Clean ™ is available through an authorized Jacuzzi Whirl-
pool Bath

©

Distributor or by calling us direct at 1-800-288-4002.

Instructions for use: Immediately after bathing and exiting the
whirlpool bath, leave the bath water in the tub and add hot water, if
necessary, so the water is at least 1" above the highest jet. Turn on
the unit without the aerator. Pour the contents of the Systems Clean
Packet 1 (taking care not to get the material on yourself) into the bath
near the intake for the circulation pump. Repeat same process with
Systems Clean Packet 2. It is important to use Packet 1 before
Packet 2 to avoid a strong odor.
Run the bath for 5 to 10 minutes.
Drain completely and rinse any residue.

If you have followed the standard purging instructions above and still
have an excess accumulation of bath residue and desire an alterna-
tive cleaning mechanism, we recommend SUPER SYSTEMS CLEAN
PLUS
manufactured by Stearns Packaging to rectify this condition.
This may be obtained by contacting us at l-800-288-4002. It is
recommended that you follow the instructions provided by the manu-
facturer with the product. Repeated use may be necessary. SUPER
SYSTEMS CLEAN PLUS
does not replace the necessity to regularly

purge your whirlpool system with Systems Clean as recommended.

(For additional information about water content, contact us for a copy

of the Jacuzzi Water Quality Primer.)

Suction Cover/Strainer Maintenance

Clean the suction cover/strainer of hair and debris when neces-

sary. To do this, remove the center screw and detach the square
cover. Clean the cover by backflushing debris from the holes. Re-
place the suction cover immediately after cleaning. When reinstall-
ing, orient the cover/strainer with the small notch at the bottom. The
gasket must be inserted into the groove of the cover/strainer before
reinstalling onto the suction fitting.

CAUTION: Keep hair a minimum of 6 inches away from the suc-
tion fitting at all times when the whirlpool system is operating.
Hair longer than shoulder length should be secured close to
the head, or a bathing cap should be worn. Do not operate the
whirlpool system with the suction cover removed! It is a safety
device and must always be in place on the suction fitting to
minimize the potential hazard of hair and body entrapment.

Bath Additives

NOTE: DO NOT USE OIL OR OIL BASED BATH ADDITIVES.
If you want to use any kind of bath additive, use only a small amount
of low-foaming powder or crystal substance; the whirlpool action
intensifies the foaming properties of soaps.

The use of certain bath oils, bubble baths and bath additives may
increase the level of accumulations of bath residue in the whirlpool
system. If excess accumulations persist, you should discontinue use
of these products.

Lamp

If your unit has chromotherapy lighting and the lights fail to func-

tion contact your Jacuzzi Whirlpool Bath

©

dealer. There are no cus-

tomer serviceable components on the chromotherapy lighting. You
may also visit our web site at http://www.jacuzzi.com/ to find the near-
est authorized service agent listing for your Jacuzzi Comfort Plus tub.

MAINTENANCE INSTRUCTIONS

11

Jacuzzi Whirlpool Bath

©

BP43000 2/05