Integra DTR-9.1 - Manual (Page 42)

42
Listening Mode Setup
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.Zone2 OSD Setup
6.About
Select: Exit:|EXIT|
Enter:|ENTER| Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
3.Listening Mode Setup
1.Mono(Analog/PCM)
2.Mono(Digital)
3.Stereo(Analog/PCM)
4.Stereo(Digital)
5.Surround(Analog/PCM)
6.Surround(Digital)
7.Theater-Dimensional
Quit:|OSD|
Menu
1.Speaker Setup
2.Input Setup
3.Listening Mode Setup
4.Preference
5.Zone2 OSD Setup
6.About
Select: Exit:|EXIT|
Enter:|ENTER| Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
3.Listening Mode Setup
1.Mono(Analog/PCM)
2.Mono(Digital)
3.Stereo(Analog/PCM)
4.Stereo(Digital)
5.Surround(Analog/PCM)
6.Surround(Digital)
7.Theater-Dimensional
Quit:|OSD|
1
2
3
4
5
6
7
8
9
0
1
2
123456789012345678901234
3-1.Mono(Analog/PCM)
a.Subwoofer :On
b.Re-EQ/Academy
:Re-EQ
c.Input Channel
:AutoL+R
d.Output Channel
:L+R
Quit:|OSD|
Currently
selected
listening mode
3-1. Mono (Analog/PCM) Setup
Select this to modify the Mono listening mode when the
current source is analog or PCM. The parameters that
can be set are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
c Input Channel Auto L+R, Left, Right Auto L+R
d Output Channel L+R, Center L+R
3-2. Mono (Digital) Setup
Select this to modify the Mono listening mode when the
current source is digital. The parameters that can be
set are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
c Input Channel Auto L+R, Left, Right Auto L+R
d Output Channel L+R, Center L+R
3-3. Stereo (Analog/PCM) Setup
Select this to modify the Stereo listening mode when
the current source is analog or PCM. The parameters
that can be set are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
c Digital Upsampling Off, On Off
The c. Digital Upsampling can only be set for PCM input
sources and cannot be set for analog ones.
3-4. Stereo (Digital) Setup
Select this to modify the Stereo listening mode when
the current source is digital. The parameters that can
be set are shown in the table below.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ/Academy Off, Re-EQ, Academy Off
3-5. Surround (Analog/PCM) Setup
Select this to modify the Pro Logic Surround listening
mode when the current source is analog or PCM. The
parameters that can be set are shown in the table be-
low.
Parameter Setting
Initial value
a Subwoofer Off, On On
b Re-EQ On, Off Off
c Surround Speakers Surround L/R, Surround Back, Surround L/R
Surround L/R+Back
d Digital Upsampling Off, On Off
The d. Digital Upsampling can only be set for PCM input
sources. Furthermore, if this is set to On, c. Surround
Speaker is fixed to “Surround L/R.”
3. Listening Mode Setup menu
This menu allows you to make fine adjustments to the
listening modes you have set for each input source with
the Listening Mode Preset sub-menu. These adjustments
are in the form of parameters and each one is ex-
plained below. Note that some parameters cannot be
set for some listening modes and that no sub-menu will
have all parameters. Also, for some input signal formats,
changes in the listening mode parameters may actually
result in no change to the resulting output signal.