Integra DTR-9.1 - Manual (Page 13)

13
R
L
FRONT
SPEAKERS
CENTER
SPEAKER
INPUT 2 PB PR Y INPUT 3 PB PR Y OUTPUT PB PR Y
IR IN
MAIN ZONE 2
AC
INLET
AC OUTLETS
AC 120V 60Hz
SWITCHED
TOTAL 120W 1A MAX.
AC OUTLETS
AC 120V 60Hz
SWITCHED
TOTAL 120W 1A MAX.
MODEL NO. DTR-9.1 AV RECEIVER
A B
12 V TRIGGER
( 6 OHMS MIN. )
( 6 OHMS MIN. )
Rear panel facilities
Optical digital input terminal
An optical digital input terminal is
equipped with a protection cap.
When connecting, remove this cap.
When not using, put the cap back
on the terminal.
AC OUTLETS
The DTR-9.1 is supplied with two AC mains outlets for
connecting the power cords from other devices so that
their power is supplied through the DTR-9.1. By doing
this, you can use the STANDBY/ON button on the DTR-
9.1 to turn on and off the connected devices as well.
COAXIAL Coaxial cable
AC-3RF Coaxial cable
OPTICAL Optical fiber cable
ANTENNA
These jacks are for connecting the FM indoor antenna
and AM loop antenna that are supplied with the DTR-
9.1.
AMP IN
These jacks are for connecting a graphic equalizer for
further control of the audio output.
• When connecting a graphic equalizer, remove the
attached jumper plugs and store them carefully so
as not to lose them.
• Only remove the jumper plugs when required. After
you finish using an AMP IN jack, replace the jumper
plug.
PRE OUT
These jacks are for connecting auxiliary power amplifi-
ers.
• When connecting auxiliary power amplifiers, re-
move the attached jumper plugs and store them
carefully so as not to lose them.
• Only remove the jumper plugs when required. After
you finish using a PRE OUT jack, replace the jumper
plug.
MONITOR OUT
There are 2 monitor outputs and each one includes
both composite video and S-video configurations.
When connecting two video monitors or televisions, be
aware that the OSD interface can only be used with
MONITOR OUT 1 (OSD will not be displayed on the
video monitor connected to MONITOR OUT 2).
DIGITAL INPUT/OUTPUT
(coaxial, optical, and input-only AC-3RF)
These are the digital audio inputs and outputs. There
are 5 digital inputs with coaxial jacks, 3 with optical
jacks, and 1 AC-3RF input. The inputs accept digital
audio signals from a compact disc, LD, DVD, or other
digital source component. For digital output, there is 1
coaxial output and 1 optical output. The digital outputs
can be connected to MD recorders, CD recorders, DAT
decks, or other similar components.
• When using the digital inputs and outputs, make
sure to also connect the analog connections when-
ever possible.
• When using one of the optical input or output jacks,
remove the protective cap and keep it safely.
When the jack is not used, replace the protective
cap.
• When using an optical input or output jack, always
use an optical fiber cable.
COMPONENT VIDEO INPUT/OUTPUT
If your DVD player or other device has component
video connectors, be sure to connect them to these
component video connectors on the DTR-9.1. The DTR-
9.1 has three component video input connectors to
obtain the color information (Y, P
B , P R ) directly from the
recorded DVD signal or other video component and
one component video output connector to output it
directly into the matrix decoder of the display device.
By sending the pure DVD component video signal di-
rectly, the DVD signal forgoes the extra processing that
normally would degrade the image. The result is vastly
increased image quality, with incredibly lifelike colors
and crisp detail.
Caution
Make sure that the total capacity of the other compo-
nents connected to this unit does not exceed the ca-
pacity that is printed on the rear panel. For this model,
the capacity is 120 watts.
Y P B P R RCA type