Marantz R3001 - Manual (Page 31)

27
ENGLISH
DISPLAY MODE
SURROUND
AV SURROUND RECEIVER SR3001
R
PHONES
PURE SETUP DIRECT SIMPLE
AUTO HT-EQ MENU ENTER
DISPLAY MEMORY
EXIT BAND
MODE
DISP MULTI AUTO TUNED ST V – OFF NIGHT PEAK ANALOG DIGITAL ATT SLEEP SURR AUTO DIRECT DISC 6.1 MT X 6.1 EQ DIGITAL SURROUND
AAC PCM L C R SL S SR LFE
S. SPEAKER B
F.DIRECT RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO 3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
You can select the display mode for the front display
of the SR3001.
To select this mode, press the DISPLAY on the front
panel or on the remote.
When this button is pressed, the display mode is
switched in the following sequence.
→ Surround Mode → Auto-display Off → Display Off
→ Input Function → Surround Mode....
In Auto display off mode, the display is off. But, if you
make a change to the unit such as input or surround
mode, the display will show that change, then go
back to off after about 3 seconds. When changing the
volume, it is not displayed.
In Display off mode, the display is off completely.
Note:
Only the DISP indicator will be illuminated on the
front display, in display off condition
OTHER FUNCTION
ATTENUATION TO ANALOG INPUT SIGNAL
DOWN UP
VOLUME
MUTE ATT DISPLAY MEMORY CLEAR
T-MODE EXIT BAND
K ANALOG DIGITAL ATT EQ DIGITAL SURROUND
AAC PCM L C R SL S SR LFE
CH.SEL LIP.SYNC
PTY SUB-T/ATT AUDIO INPUT/DISC+
F.DIRECT RDS
TUNE/SEARCH
T-MODE
TREBLE BASS
SYSTEM REMOTE CONTROLLER
RC5500SR
If the selected analog audio input signal is greater
than the capable level of internal processing, the
“PEAK” indicator will light up on the front display. If
this happens, you should press the ATT button on the
front panel or on the remote.
“ATT” indicator will be illuminated when this function is
activated. The signal-input level is reduced by about
half. Attenuation will not work with the output signal
of TAPE-OUT, CD-R/MD-OUT, VCR1-OUT and DSS/
VCR2-OUT.
This function is memorized for each individual input
source.
LISTENING THROUGH HEADPHONES
This jack may be used to listen to the SR3001’s output
through a pair of headphones. Be certain that the
headphones have a standard 1/4" stereo phono plug.
(Note that the speakers will automatically be turned off
when the headphone jack is in use.)
SURROUND
AV SURROUND RECEIVER SR3001
INPUT SELECTOR
PHONES
STANDBY
7.1CH INPUT PURE SETUP DIRECT SIMPLE
AUTO HT-EQ MENU ENTER
MODE
DISP MULTI AUTO TUNED ST V – OFF NIGH SLEEP SURR AUTO DIRECT DISC 6.1 MT X 6.1
POWER ON/OFF
S. SPEAKER B
Notes:
• When using headphones, the surround mode
will change to STEREO and TruSurround (TS)
headphones by SURROUND MODE button.
• The surround mode returns to the previous setting as
soon as the plug is removed from the jack.
VIDEO ON/OFF
When no video signal is connected to the SR3001
or a DVD, etc., is connected directly to your TV,
the unnecessary video circuit can be turned off by
selecting the “VIDEO OFF” setting.
To select video off, press the V-OFF button on the
remote.
CH.SEL LIP.SYNC
PTY SUB-T/ATT AUDIO INPUT/DISC+
F.DIRECT RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF
SELECTING ANALOG AUDIO INPUT OR
DIGITAL AUDIO INPUT
F.DIRECT RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
If you have already assigned the digital inputs, you
can temporarily select the audio input mode for
each input source with the A/D button on the remote
controller.
When this button is pressed, the input mode is
switched in the following sequence.
→ Digital Auto → Digital → Analog → Digital Auto....
In Digital Auto mode, the types of signals being input
to the digital and analog input jacks for the selected
input source are detected automatically.
If no digital signal is being input, the analog input
jacks are selected automatically.
In Digital mode, input is fi xed to an assigned digital
input terminal.
In analog mode, the analog input jacks are selected.
This selecting is temporary, so the result will not be
stored in memory.
If you need to change the input mode completely,
use INPUT setup in SETUP MENU system. (see
page 17)