Marantz R3001 - Manual (Page 12)

8
ENGLISH
RESETTING THE ALL CODE
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
AUX1
1.
ENTER
TUNE/SEARCH TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
MENU OSD
1.
2.
1. Press and hold down the any Function
Selector button and press SETUP button until
the indicator blinking twice.
2. Press the code 9 - 8 - 1.
The indicator will blink twice.
Then, RC5500SR will return to the factory
preset code.
Note:
After this procedure, the selected function button is set
initial code and other function buttons are set initial
code too.
Once you have found and the codes for your vari-
ous appliances, you may want to write them down
here.
TV
VCR
DSS
DVD
CD
TAPE
CDR
MD
SCANNING THE CODE TABLE
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
AUX1
2.
4.
4. ENTER
TUNE/SEARCH TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
2.
6.
3.
1. Switch on the appliance which should be
controlled.
2. Press and hold down the Function Selector
button for appliance which should be controlled
and press SETUP button until the indicator
blinking twice.
3. Press the code 9 - 9 - 1.
The indicator will blink twice.
4. Aim the remote control at the appliance and
slowly alternate between pressing POWER
button and the Function Selector button for
the appliance.
5. Stop when the appliance turns off.
6. Press SETUP button once to lock in the code.
CHECKING THE CODE
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
AUX1
1.
ENTER
F.DIRECT RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
1.
3.
4.
2.
1. Press and hold down the Function Selector
button for appliance which should be controlled
and press SETUP button until the indicator
blinking twice.
2. Press the code 9 - 9 - 0.
The indicator will blink twice.
3. To view the code for fi rst digit, press 1 once.
Wait 3 seconds, count the indicator blinks (e.g.
3 blinks = 3) and write down the number.
Note:
If a code digit is “0”, the indicator will not blink.
4. Repeat step 3 three more times for remaining
digits. Use 2 for the second digit, 3 for the third
digit, and 4 for the fourth digit.
PROGRAMMING THE REMOTE CONTROLLER
The remote controller RC5500SR must be
programmed to use the codes for your appliances
of different brands. This is done by keying in a 4-digit
code or by scanning the codes until the correct one is
found. We recommend to using the 4-digit code. This
mode is faster and more reliable. The code scanning
method should be used only if you cannot fi nd the
code for one of your appliances. The codes are listed
at the end of this book.
Important:
• Use the remote control buttons for programming,
not the buttons of the receiver or other appliances.
• Some codes may be not match your equipment. In
this case, your equipment cannot be controlled with
this remote controller.
PROGRAMMING WITH THE 4-DIGIT CODE
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP AUX1
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
1.
ENTER
PTY SUB-T/ATT AUDIO INPUT/DISC+
F.DIRECT RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/ 1.
2.
1. Press and hold down the Function Selector
button for the appliance which should be
controlled and press SETUP button until the
indicator blinks twice.
2. Press the 4-digit code for appliance (code table
at the end of this book)
3. When the procedure is successful, the indicator
will blink twice.
Note:
If the indicator did not blink twice, then repeat steps 1
through 2 and try entering the same code again.
¤1 PURE DIRECT button
When this button is pressed, the tone control circuit
is bypassed.
¤2 SETUP / T.TONE button
(when AMP mode is selected)
Used to enter the test tone menu.
¤3 OSD button
Note:
This button is unavailable for SR3001.
¤4 SLEEP (sleep timer) button
This button is used for setting the sleep timer. It
can be operated the same way as the button on the
unit.
¤5 TV VOLUME UP ( 3) /DOWN (4)
buttons
These buttons increase or decrease TV’s volume.