Marantz R3001 - Manual (Page 11)

7
ENGLISH
m Cursor ( 1, 2, 3, 4) / OK buttons
(when AMP mode is selected)
Use these button when operating the SETUP MAIN
MENU.
, MENU OFF button
(when AMP mode is selected)
This button is used to exit from the SETUP MAIN
MENU.
. Numeric buttons 1 to 9 / Surround
mode buttons
Numeric buttons
These buttons are used to enter fi gures in the se-
lection of a tuner preset station and station name
preset or to set select a CD track number, etc. The
functions of these buttons are dependent on the
function button selected.
Surround mode buttons
(when AMP mode is selected)
These buttons are used to select the surround
mode.
⁄0 P.SCAN (Preset scan) / V(Video)-
OFF button
(when TUNER mode is selected)
This button is used to start preset scan when
SR3001 is selected TUNER mode.
(when AMP mode is selected)
This is used when switching the video signals from
the various monitor outputs to Video-Off mode.
⁄1 0 / A/D button
0 button
This button is used to enter the number “0”
A/D button (when AMP mode is selected)
This is used to switch between the analog and digital
inputs.
⁄2 CONTROL buttons
These buttons are used when operating the CD
player, TAPE deck, etc.
The function of these buttons are dependent on
the function button selected.
For the controllable functions of each input function,
please refer to controllable function table on the page
10.
⁄3 SUB-T (Title) / ATT (attenuator)
button
When the input signal is too high and the voice
distorts even while adjusting the SR3001 VOLUME
control, turn on this function. “ATT” is illuminated
when this function is activated.
The input level is reduced. Attenuator is invalid for
the output signal of “REC OUT”.
Note:
This function is unavailable while the digital input is
selected.
⁄4 INPUT/DISC+ / CH.SEL buttons
This button is used to enter the input level setup
menu.
⁄5 TREBLE UP ( 3) /DOWN (4)
buttons
These buttons are used to adjust the tone control
of high frequency sound for left and right speaker.
⁄6 BASS UP ( 3) /DOWN (4) buttons
These buttons are used to adjust the tone control
of low frequency sound for left, right and subwoofer
speaker.
⁄7 MEMO button
Memory enable button for various preset functions.
⁄8 CLEAR button
This button is used to cancel for certain memory or
programming operations.
⁄9 DISPLAY button
Selects the display mode for the front display of the
SR3001.
¤0 NIGHT button
Pressing this button prevents the Dolby Digital
signal from playback at a loud voice. This function
reduces the voice by 1/3 to 1/4 at maximum. Thus,
it eliminates the occurrence of an abruptly loud
voice at night. However, the function is valid only in
the case when the Dolby Digital signal is entered
into OPTICAL or COAXIAL and data to compress
the voice exists in the signal to be played back.
When this button is pressed, the “NIGHT” indicator
is illuminated.
REMOTE CONTROL
OPERATION
FUNCTION AND OPERATION
The provided remote control unit is a universal
remote controller. The POWER button, numeric
buttons and control buttons are used in common
across different input source components.
The input source controlled with the remote control
unit changes when one of the input selector but-
tons is pressed.
ENTER
CH.SEL LIP.SYNC
PTY SUB-T/ATT AUDIO INPUT/DISC+
F.DIRECT RDS
TUNE/SEARCH
T-MODE
TREBLE
CHANNEL/SKIP
BASS
A/D P.SCAN/V-OFF
7.1CH IN STEREO MCH-ST
MEMO CLEAR
DISPLAY
NIGHT CSII EX/ES VIRTUAL
DTS PURE DIRECT AUTO
3 2 1
6 5 4
9 8
0
7
T.TONE MENU OFF SET UP/
MENU OSD
VOL. TV VOL. MAIN SLEEP MUTE
AMP AUX1
TUNER CD TAPE CDR/MD
DVD
POWER
VCR1 DSS/VCR2 TV
SYSTEM REMOTE CONTROLLER
RC5500SR
,
m
n
b
v
c
x
z
⁄1
⁄2 ⁄5
¤3
¤2
¤1
¤0
⁄9
⁄8
⁄7
⁄6
¤4
⁄4
⁄3
¤5
.
⁄0
z Transmitting indicator
Lights up during a button is pressed and an infra-
red signal is sending.
x (Main) POWER buttons
(when AMP mode is selected)
Press to switch the power of the SR3001 ON or
OFF after pressing the AMP button.
c Input selector buttons/ FUNCTION
SELECTOR buttons
(AUDIO/VIDEO INPUT)
These buttons are used to select a Audio or Video
source component. Press one of these buttons
once to change the function of the remote control.
Press same button within 2 seconds, the input
function of the SR3001 is changed.
Audio function sources such as CD, TAPE, CDR/MD,
and TUNER may be selected in conjunction with a
Video source.
This feature (Sound Injection) combines a sound
from one source with a picture from another.
Choose the video source fi rst, and then choose a
different audio source to activate this function.
Notes:
• CDR/MD button is set CDR function at initial. To
switch MD function, press and hold down CDR/
MD button and press 2 button.
• To return CDR function, press and hold down CDR/
MD button and press 1 button.
v MAIN VOLUME UP ( 3) /DOWN (4)
buttons
Main volume control of the SR3001. The front,
surround, center and subwoofer channel volumes
controlled by these buttons simultaneously.
b MUTE button
Muting button of the SR3001. Press this button
decrease the sound temporarily. Press this button
again to return to the previous sound.
When this button is pressed, “MUTE” indicator
lights up.
n MENU button
(when AMP mode is selected)
This button is used to enter the SETUP MAIN
MENU.