MITSUBISHI ELECTRIC WD-52631 - Manual (Page 31)

Chapter 2. TV Connections 31
DVD Player with Component Video
Component video cables and analog audio cables are
required. These are not included with the TV.
1. Connect the component video cables from Y PB
PR VIDEO OUT on the back of the DVD player to
the
COMPONENT jacks on the TV back panel,
matching the red, green, and blue colored connec-
tions.
2. Connect left (white) and right (red) stereo audio
cables from AUDIO OUT on the back of the DVD
player to COMPONENT/AUDIO LEFT and
RIGHT on the TV back panel.
7*%&0065
"6%*0065
:
-
3
1C
1S 1S
1C
3
-
:
"6%*0065
1$%7* "6%*0
"6%*0 065
$0.10/&/5
*/165
.0/*503
065
)%.*%7*"6%*0
"/5."*/ "/5"69
*&&& %*(*5"- "6%*0 065
)%.*
1$%7*
7*%&0
-&'5
3*()5
-&'5
3*()5
:
1C
1S
"6%*0 -&'5 .0/0
"6%*0 3*()5
-&'5
3*()5
4&37*$&
1035
64&8*5) $BCMF$"3%™
$BCMF$"3%™ 64&8*5) "/5$"3%501
47*%&0
7*%&0
"6%*0 -&'5
.0/0
"6%*0
3*()5
)%.*$0.1"5*#*-*5: 7*%&0JQQJQ
$0.10/&/5$0.1"5*#*-*5:
7*%&0JQQJ
%7**1$$0.1"5*#*-*5:
3&'&35008/&34(6*%&
$0.10/&/5
:
1C
1S
"6%*0 -&'5 .0/0
"6%*0 3*()5
%7%1MBZFS#BDL1BOFM
57#BDL1BOFM
Figure 13. Connecting a DVD player with component
video
IMPORTANT
See Appendix B for component video signal
compatibility information.
For digital audio connections to your A/V
receiver, see your DVD player and A/V
receiver Owner’s Guides.
A/V Receiver (Stereo System)
Most setups require either a digital audio cable or analog
stereo audio cables.
The TV makes all audio available in digital and analog
formats. Analog audio coming into the TV is available
in digital format on the
DIGITAL AUDIO OUT jack.
Digital incoming audio is available in analog format on the
AUDIO OUT LEFT/RIGHT jacks. Usually, only one of
the following connections is required:
• To connect an analog A/V receiver
Connect left (white) and right (red) audio cables from
AUDIO OUT/LEFT and RIGHT on the TV back
panel to the TV AUDIO INPUT on the A/V receiver.
• To connect a digital A/V receiver with Dolby
Digital surround sound and PCM audio support
Connect one end of the digital audio cable to
DIGITAL AUDIO OUT on the back of the TV.
Connect the other end to the COAXIAL DIGITAL
INPUT on the back of the A/V receiver.
1$%7*
"6%*0
"6%*0 065
$0.10/&/5
*/165
.0/*503
065
)%.*%7*"6%*0
"/5."*/ "/5"69
*&&& %*(*5"- "6%*0 065
)%.*
1$%7*
7*%&0
-&'5
3*()5
-&'5
3*()5
:
1C
1S
"6%*0
-&'5 .0/0
"6%*0 3*()5
-&'5
3*()5
4&37*$&
1035
64&8*5) $BCMF$"3%™
$BCMF$"3%™ 64&8*5) "/5$"3%501
47*%&0
7*%&0
"6%*0 -&'5 .0/0
"6%*0 3*()5
)%.*$0.1"5*#*-*5: 7*%&0JQQJQ
$0.10/&/5$0.1"5*#*-*5:
7*%&0JQQJ
%7**1$$0.1"5*#*-*5:
3&'&35008/&34(6*%&
"6%*0 065
%*(*5"- "6%*0 065
-&'5
3*()5
Figure 14. Connecting audio from the TV to an A/V
receiver
Note:
On rare occasions, an HDMI signal may be
copy-restricted and cannot be output from the TV
as a digital signal. To hear these copy-protected
signals through the A/V receiver, use connections
for analog A/V receivers.
Check the A/V receiver’s Owner’s Guide for
information concerning use of the digital input
and switching between digital sound and analog
stereo sound from the TV.