Grizzly G0493 - Manual (Page 23)

Model g0493 (Mfg. since 7/10)
-21-
hex Bolts M6-1 x 25 (scale Bar) ....................... 3
Flat Washers 6mm (scale Bar) ......................... 3
lock Washers 6mm (scale Bar) ........................ 3
hex nuts M6-1 (scale Bar)................................ 3
adjustable ring w/set screw (r rail) ............... 1
end Washer 8mm (r rail) ................................ 1
lock Washer 8mm (r rail) ............................... 1
Cap screw M8-1.25 x 16 (r rail) ...................... 1
lock handles M10-1.5 x 12 (rip Fence Body) .. 2
Knob M10-1.5 x 70 (rip Fence Body) ............... 1
adjustable handle M12-1.75 x 55 (Crosscut).... 1
Flat Washer 12mm (Crosscut table) ................ 1
t-nut M12-1.75 (Crosscut table) ....................... 1
t-nuts M8-1.25 (Crosscut Brace) ...................... 2
Knobs M8-1.25 x 50 (Crosscut Brace) .............. 3
Flat Washers 8mm (Crosscut Brace) ................ 2
Center stud M8-1.25 x 10 (Crosscut Fence) ..... 1
Fiber Washer 8mm (Crosscut Fence) ............... 1
t-Bolt M8-1.25 x 60 (Crosscut Fence) ............... 1
t-nuts M8-1.25 (Crosscut Fence) ...................... 3
Knob M8-1.25 (Crosscut Fence) ........................ 1
Knob M8-1.25 x 25 (Crosscut Fence) ................ 1
Flat Washer 8mm (Crosscut Fence) .................. 1
Block (Crosscut Fence) ..................................... 1
Cap screw M8-1.25 x 35 (Crosscut Fence) ...... 1
lock Washer 8mm (Crosscut Fence) ................ 1
Button hd Cap screw M8-1.25 x 40 (guard) .... 1
Flat Washer 8mm (guard) ................................. 1
if any nonproprietary parts are missing (e.g. a
nut or a washer), we will gladly replace them; or
for the sake of expediency, replacements can be
obtained at your local hardware store.
crate #2: (not shown)
sliding table ...................................................... 1
component hardware (not shown) Qty
t-Bolts (sliding table) M12-1.75 x 60 ................ 3
hex nuts M12-1.75 (sliding table) ..................... 3
Flat Washers 12mm (sliding table) ................... 3
lock Washers 12mm (sliding table) ................. 3
push handle M12-1.75 x 12 (sliding table) ....... 1
Flat Washer 12mm (sliding table)..................... 1
t-nut M12-1.75 (sliding table) ........................... 1
set screws M6-1.0 x 12 (small table) ............... 2
Cap screws M10-1.5 x 20 (small table) ............ 2
lock Washers 10mm (small table) ................... 2
Flat Washers 10mm (small table) .................... 2
Cap screws M10-1.5 x 20 (large table) ........... 4
lock Washers 10mm (large table) .................. 4
Flat Washers 10mm (large table) .................... 4
set screws M10-1.5 x 25 (large table) ............ 4
Cap screw M10-1.5 x 30 (hose support) .......... 1
lock Washer 10mm (hose support) ................. 1
hex nut M10-1.5 (hose support) ...................... 1
Cap screws M10-1.5 x 30 (support Brace) ....... 4
lock Washer 10mm (support Brace) ................ 4
hex nut M10-1.5 (support Brace) ..................... 2
NOTICE
some hardware/fasteners on the inventory
list may arrive pre-installed. check mount-
ing locations on main components before
assuming inventory list items are missing.
box 8 & 9: (figure 16) Qty
v. scale Bar .................................................... 1
W. Crosscut table Brace ................................. 1
X. rip Fence ................................................... 1
figure 16. Box 8 & 9 contents.
W
X
v