Fortinet FortiBridge 2002F - Manual (Page 2)

LED Description Package Contents
FortiBridge 2002F
USB2
CONSOLE2 MODEM2 MGMT2
INT3
INT4
INT3
INT4
EXT3
EXT4
EXT3
EXT4
HA2
PWR2 NORMAL2
BYPASS2
MODE2 RESET2
FortiGate
USB1
CONSOLE1
FortiGate
MODEM1 MGMT1
INT1
INT2
INT1
INT2
EXT1
EXT2
EXT1
EXT2
HA1
PWR1 NORMAL1
BYPASS1
MODE1 RESET1
DISCONNECT TWO POWER SUPPLY CORDS BEFORE SERVICING DISCONNECT TWO POWER SUPPLY CORDS
BEFORE SERVICING
Ground
AC power
connection
Power button Power button
AC power
connection
USB1
Console1
Modem1
Management1
LEDs USB2
Console2
Modem2
Management2
LEDs
INT1 and
INT2
EXT1 and
EXT2
INT3 and
INT4
EXT3 and
EXT4
Mode1
Reset1
Mode2
Reset2
LEDs LEDs
Interface Description
Connecting
Administrator user name admin
Administrator password (none)
NAT/Route mode
Management1
192.168.1.99
Management2 0.0.0.0
To reset the unit to the factory defaults, in the CLI type the command:
execute factory reset
FortiGate-30B
Tools and Documenation
Copyright 2010 Fortinet Incorporated. All rights reserved. Trademarks Products mentioned in this document are trademarks.
QuickStart Guide
Straight-through
Ethernet cable
Power cable x2 DB9-RJ45 Serial
cable
REGISTER
SFP SX x4
FortiBridge 2002F USB2 CONSOLE2 MODEM2 MGMT2 INT3
INT4
INT3 INT4
EXT3
EXT4
EXT3 EXT4 HA2 PWR2 NORMAL2 BYPASS2 MODE2 RESET2 FortiGate USB1 CONSOLE1 FortiGate MODEM1 MGMT1 INT1
INT2
INT1 INT2
EXT1
EXT2
EXT1 EXT2 HA1 PWR1 NORMAL1 BYPASS1 MODE1 RESET1
Factory Defaults
LED State Description
Power
Green The unit is powered on.
Off The unit is powered off.
Normal
Green The unit is being used in Normal
mode.
HA
Green The unit is being used in a HA cluster.
Off The unit is in stand-alone mode.
Bypass
Green Bypass network activity at this inter-
face.
Off Normal status.
INT and
EXT LEDs
Green The correct cable is in use and the
connected equipment has power.
Off No link established or the interface
has been turned off.
MGMT1
and
MGMT2
Ports
Link/Activity (left) Green Port has power and network connec-
tion.
Link/Activity (left) Green
flashing
Network data is being sent or re-
ceived.
Speed (right) indicator is
Green
Connected at 1000 Mbps.
Speed (right) indicator is
Amber
The interface is connected at 100
Mbps.
Speed (right) indicator
is Off
The interface is connected at 10
Mbps.
Interface Type Speed Proto-
col
Description
Console1
and Con-
sole2
RJ-45 9600 bps
8/N/1
RS-232
serial
Connection to the manage-
ment computer. Provides
access to the command line
interface (CLI).
Modem1
and Mo-
dem2
RJ-45 Connection to external serial
modem with full handshak-
ing.
USB1 and
USB2
USB USB Two optional connections to
a USB key for installation.
MGMT1
and
MGMT2
RJ-45 10/100/1000
Base-T
Ethernet Two management ports.
INT1, INT3,
EXT1, and
EXT3
LC
SFP
1000Base-SX Ethernet Fiber optic connections to
gigabit optical networks.
INT2,
INT4,
EXT2, and
EXT4
SFP 1GB-SX Ethernet Small form-factor pluggable
transceiver.
Connect the FortiBridge unit to the internal and external networks and the Forti-
Gate unit. Normally, you would use straight-through ethernet cables to connect
the FortiBridge unit. However, for some connections you may need a crossover
ethernet cable (for example, for compatibility with network devices that do not
support Auto MDI/MDIX).
•
Connect the FortiBridge INT 2 interface to the FortiGate unit internal inter-
face.
• Connect the FortiBridge EXT 2 interface to the FortiGate unit external inter-
face.
• Connect the FortiBridge INT 1 interface to the internal network.
• Connect the FortiBridge EXT 1 interface to the external network.
• Turn on the FortiGate unit and any network equipment that was turned off.
• Connect the power cords at the back of the FortiBridge unit. Plug the other
end of the power cables into a grounded electrical outlet.
• The PWR and Bypass Mode LEDs turn on. After a short time, the Forti-
Bridge unit switches to Normal mode. The Bypass LED turns off and the
Normal LED turns on.
Note: To ground the unit, use a minimum of 18 AWG (UL Certification) wire with
ring terminals. One end connects to the ground on the back of the unit and the
other end connects to the bracket on the chassis.
Caution: Disconnect both power sources before servicing.