FujiFilm E510 - Manual (Page 53)

105 104
Some frames may be protected.
A language other than English is
selected in the “
” setting in
the “SET-UP” menu ( ➡P.70).
i The camera volume is set too low.
i The microphone was blocked during
shooting/recording.
i There is something covering the
speaker during playback.
i The camera is not connected to the
TV correctly.
i “TV” is selected as the TV input.
i The video output setting is incorrect.
The video output setting is incorrect.
i The USB cable (included) is not
correctly connected to the PC or
camera.
i The PC is not turned on.
The camera has suffered an
unforeseen problem.
“ ® ” is not selected in USB mode in
the “SET-UP” menu.
Frame erase does
not erase the frame.
The ERASE ALL
function does not
erase all the frames.
Screens are not
displayed in English.
The camera does not
emit any sound.
There is no image on
the TV.
The TV image is
black and white.
When the camera is
connected to a PC,
the photographed
image appears on
the camera’s LCD
monitor.
The camera no longer
works correctly.
Can’t print with
PictBridge.
The camera was
connected to a PC
when the USB mode
was set to “
® ”.
Unprotect frames using the camera on
which the protection was first applied.
1Press the “MENU/OK” button to
display the menu.
2Press “d” or “c” to select “F” and
press “a” or “b” to select “SET-UP”.
SET-UP screen appears on the LCD
monitor.
3Press “d” or “c” to move to option 3
and then press “a” or “b” to select
“
”.
4Press “d” or “c” several times to
select “ENGLISH”.
5Press the “MENU/OK” button.
i Adjust the volume.
i Take care not to block the microphone
during shooting/recording.
i Make sure that the speaker is
uncovered.
i Connect the camera and TV correctly.
i Set the TV input to “VIDEO”.
i Change the setting to “NTSC” or
“PAL” ( ➡P.70).
Change the setting to “NTSC” or “PAL”
(
➡P.70).
i Set up the camera and the USB cable
(included) correctly.
i Turn the PC on.
Briefly remove the batteries or
disconnect the AC power adapter.
Then, reload the batteries or reconnect
the AC power adapter and try again.
Select “ ® ” in USB mode in the
“SET-UP” menu.
Perform steps 1 to 3 to remove the
camera from the PC.
h Windows
1 The “New Hardware Found” wizard
(or “Scanner and Camera” wizard)
appears. If the wizard does not
appear, proceed to step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the PC.
h Macintosh
1 The window for locating the driver
appears. If the window does not
appear, proceed to step 3.
2 Click the [Cancel] button.
3 Disconnect the camera from the
Macintosh.
Troubleshooting Possible causes Solutions
Troubleshooting
eIf you think the camera is faulty, check the following once more.
Troubleshooting Possible causes Solutions
No power.
Power cuts out during
operation.
Batteries run out
quickly.
No photograph is
taken when the
shutter button is
pressed.
Can’t use the flash.
The flash settings are
restricted and cannot
be selected.
The playback image
is dark even though
the flash was used.
The image is blurred.
There is speckling on
the image.
Can’t format the xD-
Picture Card.
i The batteries have run out.
i The batteries are loaded backwards.
i The battery cover is not closed
correctly.
i The AC power adapter plug has
come out of the power outlet.
The batteries have run out.
i Camera is being used in extremely
cold conditions.
i The terminals are soiled.
i The batteries can no longer be
recharged.
i The rechargeable batteries (if used)
have become deactivated, or the
battery capacity has diminished due
to the memory effect.
i No xD-Picture Card is inserted.
i The xD-Picture Card is full.
i The xD-Picture Card is not formatted.
i The xD-Picture Card contact area is
soiled.
i The xD-Picture Card is damaged.
i The Auto power off function has
turned the camera off.
i The batteries have run out.
i The shutter button was pressed while
the flash was charging.
i The flash is not popped up.
i The Mode dial is set to “
, ”
Landscape.
The Mode dial is set to “ , ”, “ . ” or
“ / ”.
i The subject is too far away.
i Your finger was covering the
flash/flash control sensor.
i The lens is dirty.
i The photographed subject was too
dark.
i You photographed scenery with
Macro mode selected.
i You took a close-up shot without
selecting Macro mode.
i You are shooting a subject that is not
suited to autofocusing.
The picture was taken with a slow
shutter speed (long exposure) in a
high-temperature environment.
The xD-Picture Card contact area is
soiled.
i Load new or fully charged batteries.
i Load the batteries in the correct
direction.
i Close the battery cover correctly.
i Plug the adapter back in.
Load new or fully charged batteries.
i Put the batteries in your pocket or
another warm place to heat them and
then load them into the camera just
before you take a picture.
i Wipe the battery terminals with a
clean, dry cloth.
i Load new or fully charged batteries.
i Use the rechargeable battery
discharging function to restore the
rechargeable batteries to full
capacity.
i Insert an xD-Picture Card.
i Insert a new xD-Picture Card or
erase some unwanted frames.
i Format the xD-Picture Card on the
camera.
i Wipe the xD-Picture Card contact
area with a clean dry cloth.
i Insert a new xD-Picture Card.
i Turn the camera on.
i Load new or fully charged batteries.
i Wait until the charging is completed
before pressing the shutter button.
i Pop up the flash.
i Change the Photography mode.
The flash settings are restricted
because the camera settings are
tailored to the scene being shot.
Change the Photography mode for a
wider range of flash settings.
i Move to within the effective flash
range before taking the picture.
i Hold the camera correctly.
i Clean the lens.
i Try standing about 2 m (6.6 ft.) from
your subject to take the picture.
i Cancel Macro mode.
i Select Macro mode.
i Use AF/AE lock to take the picture.
This is a characteristic of CCDs and
does not indicate a camera fault.
Wipe the xD-Picture Card contact area
with a clean dry cloth.