Hitachi SJ300 Series - Manual (Page 28)

28
Chapter 3 – Parameter Setting Tables
Function mode
Code Function name Setting range Initial data remarks
C040
Overload advance notice
signal output mode
00(On accel. And decel, constant speed)/01(Only constant speed) 01
C041 Overload advance notice level 0.0-2.0*rated current(A)
Inverter
rated current
*C042
Frequency arrival setting for
acceleration.
0.00-99.99/100.0-400.0(Hz) 0.00
*C043
Arrival frequency setting for
deceleration.
0.00-99.99/100.0-400.0(Hz) 0.00
*C045
Frequency arrival setting for
acceleration 2.
0.00-99.99/100.0-400.0(Hz) 0.00
*C046
Arrival frequency setting for
deceleration 2.
0.00-99.99/100.0-400.0(Hz) 0.00
C055
Over torque level setting
(Forward-driving)
0.-200.(%) 100.
C056
Over torque level setting
(Reverse-regenerating)
0.-200.(%) 100.
C057
Over torque level setting
(Reverse-driving)
0.-200.(%) 100.
C058
Over torque level setting
(Forward-regenerating)
0.-200.(%) 100.
C061
Thermal warning level
setting
0.-100.(%) 80.
C062 Alarm code selection 00(Invalid)/01(3bit)/02(4bit) 00
*C063
Zero speed detection level
setting
0.00-99.99/100.(Hz) 0.00
C070 Data command 02(operator)/03(RS485)/04(option1)/05(option2) 02
C071
Communicating transmission
speed 02(loop-back test)
03(2400bps)/04(4800bps)/05(9600bps)/06(19200bps)
04
C072 Communication code 1. -32. 1.
C073 Communication bit 7(7bit)/8(8bit) 7
C074 Communication parity 00(no parity name)/01(even parity)/02(odd parity) 00
C075 Communication stop bit 1(bit)/2(bit) 1
C078 Communication waiting time 0.-1000.(ms) 0.
C081 O adjustment 0.-9999./1000-6553(10000-65530)
Setting on
forwarding
C082 OI adjustment 0.-9999./1000-6553(10000-65530)
Setting on
forwarding
C083 O2 adjustment 0.-9999./1000-6553(10000-65530)
Setting on
forwarding
C085 Thermistor adjustment 0.0 - 1000. 105.0
C086 AM offset adjustment 0.0 - 10.0(V) 0.0
C087 AMI adjustment 0. - 255. 80
C088 AMI offset adjustment 0. - 20.0(mA)
Setting on
forwarding
b034 RUN time/Power ON time level 0.-9999./1000-6553(10000-65530)hr 0.
b036 Start reduced voltage 00(Start reduced voltage time small)-06(Start reduced voltage time large) 06
b037 Display selection 00(all display)/01(each function display)/02(User setting / main setting) 00
b040 Torque limit mode selection
00(4 quadrant mode)/01(Terminal operation)/
02(Analog input)/03(Option1)/04(Option2)
00
b041
Torque limit level 1 setting
(Forward-driving at
4 quadrant mode)
0.-200.(%)/no(Invalid) 150.
b042
Torque limit level 2 setting
(Reverse-regenerating at
4 quadrant mode)
0.-200.(%)/no(Invalid) 150.
b043
Torque limit level 3 setting
(Reverse-driving at
4 quadrant mode)
0.-200.(%)/no(Invalid) 150.
b044
Torque limit level 4 setting
(Forward-regenerating at
4 quadrant mode)
0.-200.(%)/no(Invalid) 150.
b045 Torque LAD-STOP selection 00(Invalid)/01(Valid) 00
b046
Reverse run prevention
selection
00(Invalid)/01(Valid) 00
b080 AM adjustment 0. - 255. 180
b081 FM adjustment 0. - 255. 60
*b082 Start frequency adjustment 0.10-9.99(Hz) 0.10
b083 Carrier frequency setting 0.5-15.0(kHz) Derating enable, <0.5-10kHz> 5.0
b084 Initialize mode
00(Trip history clear)/01(Data initialization)/
02(Trip history clear + data initialization)
00
b086
Frequency scalar conversion
factor
0.1-99.9 1.0
b087 STOP key enable 00(valid)/01(invalid) 00
O
u
tput t
e
rm
inal s
tat
e s
e
tt
ing •
O
u
tput lev
e
l
s
e
tt
ing
C
o
m
m
u
ni
cati
on
functio
n
a
d
justm
e
n
t
A
n
a
log
me
te
r se
tt
ing
Miscel
laneou
s