Tv setup wizard, First time use 13 – Hitachi LE46S704 User Manual

Page 13

FIRST TIME USE

TV Setup Wizard

Setup Wizard (5/8)

Please select TV RF tuning band ...

Move

Select

SEL

Air

Cable

Cancel

The sixth step will start the scanning feature to find the channels

available on the antenna or cable system. Press the SELECT

button on the remote control to start the channel scan.

Setup Wizard (6/8)

Please check that the RF cable is

connected properly.

Scan time may take over 20 minutes.

Move

Select

SEL

Start

Cancel

The seventh step is the channel scanning process, it shows the

scan of digital channels first and then the analog channels next.

The scanning process will show how many channels have been

found. Please be patient while the scanning process searches

for the available channels in your area. If you wish to cancel the

process, press the SELECT button on the remote control.

Setup Wizard (7/8)

Searching, Please wait...

Searching Digital CH

Channel 3

Digital Channels Found

Analog Channels Found

Select

SEL

Skip

Once the user cancels the wizard, the wizard will

•

not be shown again.

If you see the screen above and if you did not

•

connect your antenna cables to your TV, turn off

your TV, unplug the power cord and connect your

cables according to the applicable connections in

the “First Time Use” section of this Owners Guide.

After completing the TV Setup Wizard, these

•

screens will not appear again. For updating and

adding the channels available in your area refer to

the Add Channels to List feature on page 40.

The last step is the completion of process, it shows a brief message

and you are ready to view TV programing. This final message will

be shown for a few seconds and then the first detected channel will

be tuned in. You may also press EXIT button on the remote control

to tune to the first detected channel.

Setup Wizard (8/8)

Congratulations. TV Setup is done.

Exit

EXIT

Your Hitachi LCD television has a TV Setup Wizard feature which has the ability to help you easily setup the first time you turn on your TV

and find the channels available in your area. Please follow the instructions below.

The first time you turn on your Hitachi LCD TV, the Energy Savings

Initial settings screen will appear. Please select either Home or

Retail mode settings to advance to the TV Setup Wizard screen.

If you select Home mode, this will save energy, and is intended

for home use. Retail mode will set the Picture to Dynamic default

settings and the picture will be brighter. This setting is intended for

showroom and shop use. If later you want to change the Energy

Savings Initial Settings, you can use the Setup menu (refer to page

37).

Setup Wizard (1/8)

Please select Home/Retail ...

Home mode default settings are recommended for
in-home use. ENERGY STAR qualified.

Retail mode is intended for in-store display and resets
video settings at AC Power On.

Move

Select

SEL

Home

Retail

NOTE

Retail mode is intended for showroom or shop use.

If you make adjustment changes in this mode, they

will not be saved when TV’s AC power is lost (e.g.

power cord unplugged).

The TV Setup Wizard screen automatically starts after the Energy

Savings Initial Settings the first time the TV is turned on.

The second step is to set the language of your TV On Screen

Menu. Select the language that you prefer. Use the CURSOR PAD

to select language and press the SELECT button on the

remote control.

Setup Wizard (2/8)

Please select language ...

Move

Select

SEL

English

Español

Français

Cancel

The third and fourth steps are to set the date and time. There are

two options; one for automatic time setting in which you will select

only the time zone in your area and the second option is a manual

setup for the date and time. Use the CURSOR PAD to select and

change the options with the remote control.

Setup Wizard (4/8)

Please select Time Zone ...

Move

Select

SEL

Cancel

NST

MST

AST

PST

EST

AKST

CST

HST

Setup Wizard (4/8)

Please enter the date and time ...

Move

Select

SEL

Year

2010

Month

Jan

Date

Time

3:59 AM

Cancel

Setup Wizard (3/8)

Please select Time mode ...

Move

Select

SEL

Auto

manual

Cancel

The fifth step is designed to find broadcasting or cable channels.

There are two options, Air for an external antenna and Cable for a

cable system provider in your home. Use the CURSOR PAD p

to select a source and press the SELECT button on the remote

control.

NOTES

This manual is related to the following products:

LE42S704