Edirol V-4 - Manual (Page 96)

96
MIDI Implementation
● A ch effect 4
This specifies effect 4 on/off and the parameter for channel A in Normal mode or the base
channel in Presentation mode.
With the factory settings this is unassigned.
Values are 0, 1--127, corresponding to OFF, ON:0--Max.
● B ch effect 1
This specifies effect 1 on/off and the parameter for channel B in Normal mode.
With the factory settings this is unassigned.
Values are 0, 1--127, corresponding to OFF, ON:0--Max.
● B ch effect 2
This specifies effect 2 on/off and the parameter for channel B in Normal mode.
With the factory settings this is unassigned.
Values are 0, 1--127, corresponding to OFF, ON:0--Max.
● B ch effect 3
This specifies effect 3 on/off and the parameter for channel B in Normal mode.
With the factory settings this is unassigned.
Values are 0, 1--127, corresponding to OFF, ON:0--Max.
● B ch effect 4
This specifies effect 4 on/off and the parameter for channel B in Normal mode.
With the factory settings this is unassigned.
Values are 0, 1--127, corresponding to OFF, ON:0--Max.
● Transition Select
Selects the type of transition.
With the factory settings this is unassigned.
Values are 0-2, corresponding to Transition 1, Transition 2 and Transition 3.
● Transformer A
Turns channel A TRANSFORMER on/off.
With the factory settings this is unassigned.
Values are 0-63 and 64-127, corresponding to OFF and ON.
● Transformer B
Turns channel B TRANSFORMER on/off.
With the factory settings this is unassigned.
Values are 0--63 and 64--127, corresponding to OFF and ON.
● Output Fade
Controls OUTPUT FADE.
With the factory settings this is unassigned.
Values are 0 - 64 - 127, corresponding to Black - Center - White.
● BPM Sync
Switches BPM SYNC on/off.
With the factory settings this is unassigned.
Values are 0-63 and 64-127, corresponding to OFF and ON.
● Video Fader
Controls the VIDEO FADER.
With the factory settings this is assigned to CC#11 (Expression).
Values are 0-127, corresponding to A (base)-B (sub).
■ Factory Setting of V-LINK
The factory setting of V-LINK (receipt of V-LINK ON message only) is as follows.
+————————————————————————————————————————————————————————————————+
|Parameter
|Assign | Value |
+————————————————————————————————————————————————————————————————+
|V—4 Mode
|— |Presentation Mode |
|Note Mode |— |OFF |
|Rx Channel |— |1 |
|Tx Channel |— |1 |
|Input Select |— |Ach : 1 |
| | |Bch : 2 |
|Memory Select |— |1 |
|Transition TimeCC#5(Portament Time |0.0 sec |
|A ch Effect 1 |OFF |OFF |
|A ch Effect 2 |OFF |OFF |
|A ch Effect 3 |OFF |OFF |
|A ch Effect 4 |OFF |OFF |
|B ch Effect 1 |OFF |OFF |
|B ch Effect 2 |OFF |OFF |
|B ch Effect 3 |OFF |OFF |
|B ch Effect 4 |OFF |OFF |
|Transition | | |
|Select |OFF |1 |
|Transformer A |OFF |OFF |
|Transformer B |OFF |OFF |
|Output Fade |OFF |Center |
|BPM Sync |OFF |OFF |
|Video Fader |CC#11(Expression) |A 100% |
+————————————————————————————————————————————————————————————————+
* When V-LINK is off, V-LINK message will be ignored.
* The changes of setting done while V-LINK is on will not be saved.
* When V-LINK is turned off, the setting before V-LINK turned on will be recalled.