For your safety, Important safety instructions – FujiFilm X-H2 Mirrorless Camera User Manual

Page 370

346

echnical Not

For Your Safety

IMPORTANT SAFETY INSTRUCTIONS

•

Read Instructions

: All the safety and operating instructions

should be read before the appliance is operated.

•

Retain Instructions

: The safety and operating instructions

should be retained for future reference.

•

Heed Warnings

: All warnings on the appliance and in the

operating instructions should be adhered to.

•

Follow Instructions

: All operating and use instructions

should be followed.

Installation

Power Sources

: This video product should be operated only

from the type of power source indicated on the marking la-
bel. If you are not sure of the type of power supply to your
home, consult your appliance dealer or local power com-
pany. For video products intended to operate from battery
power, or other sources, refer to the operating instructions.

Grounding or Polarization

: This video product is equipped

with a polarized alternating-current line plug (a plug having
one blade wider than the other). This plug will ﬁ t into the
power outlet only one way. This is a safety feature. If you are
unable to insert the plug fully into the outlet, try reversing
the plug. If the plug should still fail to ﬁ t, contact your electri-
cian to replace your obsolete outlet. Do not defeat the safety
purpose of the polarized plug.

Alternate Warnings

: This video product is equipped with

a three-wire grounding-type plug, a plug having a third
(grounding) pin. This plug will only ﬁ t into a grounding-type
power outlet. This is a safety feature. If you are unable to
insert the plug into the outlet, contact your electrician to re-
place your obsolete outlet. Do not defeat the safety purpose
of the grounding type plug.

Overloading

: Do not overload wall outlets and extension

cords as this can result in a risk of ﬁ re or electric shock.

Ventilation

: Slots and openings in the cabinet are provided

for ventilation, to ensure reliable operation of the video prod-
uct and to protect it from overheating, and these openings
must not be blocked or covered. The openings should never
be blocked by placing the video product on a bed, sofa, rug,
or other similar surface.

This video product should not be placed in a built-in instal-
lation such as a bookcase or rack unless proper ventilation is
provided or the manufacturer’s instructions have been ad-
hered to. This video product should never be placed near or
over a radiator or heat register.

Attachments

: Do not use attachments not recommended by

the video product manufacturer as they may cause hazards.

Water and Moisture

: Do not use this video product near wa-

ter—for example, near a bath tub, wash bowl, kitchen sink,
or laundry tub, in a wet basement, or near a swimming pool,
and the like.

Power-Cord Protection

: Power-supply cords should be routed

so that they are not likely to be walked on or pinched by
items placed upon or against them, paying particular atten-
tion to cords at plugs, convenience receptacles, and the point
where they exit from the appliance.

Accessories

: Do not place this video product on an unstable

cart, stand, tripod, bracket, or table. The video product may
fall, causing serious injury to a child or adult, and serious
damage to the appliance. Use only with a cart, stand, tripod,
bracket, or table recommended by the manufacturer, or sold
with the video product. Any mounting of the appliance
should follow the manufacturer’s instructions, and should
use a mounting accessory recommended by the manufac-
turer.

An appliance and cart combination
should be moved with care. Quick
stops, excessive force, and uneven
surfaces may cause the appliance and
cart combination to overturn.

Antennas

Outdoor Antenna Grounding

: If an outside antenna or cable

system is connected to the video product, be sure the an-
tenna or cable system is grounded so as to provide some
protection against voltage surges and built-up static charges.
Section 810 of the National Electrical Code, ANSI/NFPA No.
70, provides information with respect to proper grounding of
the mast and supporting structure, grounding of the lead-in
wire to an antenna discharge unit, size of grounding con-
ductors, location of antenna discharge unit, connection to
grounding electrodes, and requirements for the grounding
electrode.

EXAMPLE OF ANTENNA GROUNDING AS

PER NATIONAL ELECTRICAL CODE

Ground Clamp

Electric Service Equipment

e Equipment

Antenna Lead
in Wire

Antenna

An
Discharge Unit

D
(NEC SECTION

810-20)

Ground Clamps

Power Service Grounding Electrode
System (NEC ART 250. PART H)

Grounding
Conductors (NEC
SECTION 810-21)