Roland TD-27KV2 V-Drums Electronic Drum Kit - Manual

NOTE
• When setting-up or adjusting the stand, take care not to pinch your fingers between movable parts and the main unit. If using this in a location where children are present, be sure to provide adult supervision or guidance.
• Prepare an area in which you can perform the assembly safely.
• Do not use a power tool (e.g., an electric screwdriver) to assemble the stand. You risk damaging or stripping the screws.
• When removing the parts from the packing carton, take care that your box cutter or other sharp implement does not scratch the pipes.
• If you will be using this drum stand for an extended period of time in the same location, we recommend that you use a drum mat (TDM series) made by Roland to prevent the rubber feet from soiling the surface on which they are placed.
Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES.” After reading, keep the document(s)
where it will be available for immediate reference.
Roland, V-Drums are either registered trademarks or trademarks of Roland Corporation in the United States and/or other countries.
Owner’s Manual
© 2019 Roland Corporation
How to Set Up the Stand
1. Check the parts
Before you start assembling the stand, make sure that
you have all of the parts.
1
2
3
4
5 6
7
8
10
9
11
12
13
Number Name Quantity
1 Straight pipe L (Long) 1
2 Curved pipe L
(with one pad mount, with one memory lock) 1
3 Center pipe (upper) (with two pad mounts) 1
4 Center pipe (lower) 1
5 Main unit pipe L (second holder higher) 1
6 Main unit pipe R (second holder lower) 1
7
Curved pipe R
(with two pad mounts, with one memory lock)
1
8 Straight pipe R (Short) 1
9 Cymbal mount 3
10 Pad mount 3
11 Cable clip 4
12 Drum key 1
13 Cable tie 4
2. Assembling the center section
2–1. Attach the center pipes (upper 3 /lower 4 ) to the
main unit pipe L 5 .
• Insert the center pipe (upper) 3 into the top
holder of the main unit pipe L 5 .
• Insert the center pipe (lower) 4 into the third
holder from the top.
Center pipe (upper) 3
Main unit pipe L 5
Center pipe (lower) 4
Align the guide hole with the gap of the holder,
and tighten (two locations) using the drum key 12 .
2–2. Attach the main pipe R 6 .
• Insert the center pipe (upper) 3 into the top
holder of the main unit pipe R 6 .
• Insert the center pipe (lower) 4 into the
second holder.
Center pipe (upper) 3
Main unit pipe R 6
Center pipe (lower) 4
Align the guide hole with the gap of the holder,
and tighten (two locations) using the drum key 12 .
3. Attaching the left arm section
3–1. Position the second holder from the top of the main
unit pipe L
5 facing outward, and insert the curved
pipe L 2 .
Curved pipe L 2
Main unit pipe L 5
Align the guide hole with the gap of the holder,
and tighten using the drum key 12 .
3–2. Align the memory lock with the holder, and tighten
using the drum key
12 .
Align positions
Memory lock
3–3. Attach the straight pipe L 1 .
Align the guide hole with the gap of the holder,
and tighten using the drum key 12 .
Straight pipe L 1
4. Attaching the right arm section
4–1. Position the bottom holder of the main unit pipe R 6
facing outward, and insert curved pipe R 7 .
Curved pipe R 7
Main unit pipe R 6
Align the guide hole with the gap of the holder,
and tighten using the drum key 12 .
4–2.
Align the memory lock with the holder, and tighten
using the drum key
12 .
4–3. Attach the straight pipe R 8 .
Align the guide hole with the gap of the holder,
and tighten using the drum key 12 .
Straight pipe R 8
4–4. Verify that the four vertical pipes are truly vertical.
If the stand wobbles when placed on the floor,
loosen the holders and make adjustments.
5.
Assembling the cymbal mount
5–1. Loosen the hand knob and pull out the rod.
Hand knob
Joint
Rod
5–2. Rotate the joint and insert the rod.
Joint
5–3. Tighten the hand knob.
6.
Attaching the pad mounts and cymbal mounts
Pad mounts 10
Cymbal mounts 9
6–1.
Raise the mount holders (three locations) of the
center pipe (upper)
3 and the curve pipe R 7 .
Mount holders
6–2. Attach pad mounts 10 to the holders that you raised,
and tighten using the hand knobs (three locations).
Hand knobs
6–3. Attach the cymbal mounts 9 in the positions shown
in the illustration, and tighten using the hand knobs
(three locations).
Notes
• When setting up or storing the stand, be careful not
to pinch the fingers you use to handle the stand.
• Regarding the way of mounting a drum sound
module, pads, or cymbals, please refer to the setup
guide of your drum kit.
Aligning the position of pipes and holders
Align the guide hole with the gap of the holder
Rotate the inserted
pipe, adjusting it so
that the guide hole is
visible through the gap
of the holder.
Guide hole
Gap
Rotate pipe to adjust
Use the cable clips 11 and cable ties 13 to manage the cables
neatly when attaching the pads and the sound module.
When setting up, pay attention to safety so that the stand does not fall over.
Refer to the setup guide of your drum kit, and observe the safety precautions when setting up.
Assembly for a Left-Handed Player
For left-handed use, assemble the stand with left and right reversed as shown in the illustration.
• Before you begin work, loosen the memory locks of curved pipes L 2 and R 7 . When you finish assembly,
adjust the position and retighten.
• For the position at which to attach each mount, refer to the setup guide of your drum kit.
Straight pipe L 1
Center pipe (upper) 3
Center pipe (lower) 4
Main unit pipe L 5
Straight pipe R 8
Pad mount 10
Main unit pipe R 6
Cymbal mount 9
Memory lock
Curved pipe L 2
Curved pipe R 7
Aligning the position of pipes and holders
1.
Turn the inserted pipe to align the guide hole with
the holder notch (the mark at which to align the
memory lock), and push it all the way in.
Holder notch
Guide hole
Adjusting the memory lock
1.
Use the drum key 12 to loosen the screw of the
memory lock.
2.
Rotate the memory lock 180 degrees, and align
the holder notch with the memory lock mark.
Align positions
Memory lock
3.
Use the drum key 12 to securely tighten the
memory lock screw.
2
English