Roland DTS-30S Heavy-Duty Stand for V-Drums - Manual

© 2021 Roland Corporation
English
Owner’s Manual
Caution when Setting Up
5 Prepare an area in which you can perform the assembly safely.
5 When setting up and adjusting the stand, make sure that your
fingers don’t get pinched in the gaps between the pipes, knobs or
holders. If using this in a location where children are present, be
sure to provide adult supervision or guidance.
5 Regarding the way of mounting a drum sound module, pads, or
cymbals, please refer to the Owner’s Manual supplied with them.
5 Check the marking labels on both ends of the cables when
connecting them. For details on how to make the connections, refer to the
Owner’s Manual of the drum sound module you are using.
The names on the labels correspond to trigger input jack names as
follows.
Label KIK T1 T2 T3 T4
Jack KICK TOM 1 TOM 2 TOM 3 TOM 4
Label CR1 CR2 AX1 AX2 AX3 AX4
Jack CRASH1 CRASH2 AUX 1 AUX 2 AUX 3 AUX 4
5 When disconnecting all cables, grasp the connector itself—never pull on
the cable. This way you will avoid causing shorts, or damage to the cable’s
internal elements.
5 The AUX 1–4 cables have a female plug at the pad end. Since they cannot
be connected directly to the pad, you’ll need to provide connection cables
separately.
5 There are no connection cables for snare/ride/hi-hat. You’ll need to
provide them separately.
5 When connecting to a V-pad, V-cymbal or V-hi-hat that is equipped with a
DIGITAL TRIGGER OUT port, use the connection cable included with that
product.
5 Never pull on any cables with excessive force.
5 Fasten the cables so that they will not obstruct your playing; use cable
ties. Make sure to wrap the cable ties around the stands.
5 If you will be using this drum stand for an extended period of time in the
same location, we recommend that you use a drum mat (TDM series)
made by Roland to prevent the rubber feet from soiling the surface on
which they are placed.
USING THE UNIT SAFELY
Check the Included Items
After opening the package, check that all of the included items are present. If anything is missing, contact your dealer.
* Before using this unit, carefully read “USING THE UNIT SAFELY” and “IMPORTANT NOTES” for each product to use them correctly. Also, be sure to keep this
Owner’s Manual handy, so that you can quickly refer to it when needed.
8 DBS-30 × 1
8 DCS-30 × 2
8 PDS-20 × 1
8 Connecting cables (set of 11 cables)
× 1
8 Cable tie × 4
8 Owner’s Manuals
8 DTS-30S Owner’s Manual
8 DBS-30/DCS-30 Owner’s Manual
8 PDS-20 Owner’s Manual
* The two DCS-30 stands are
symmetrical.
DBS-30 DCS-30 PDS-20
Cable tie
Main Specifications
Configuration
Drum boom stand: DBS-30 x 1
Drum combination stand: DCS-30 x 2
Pad stand: PDS-20 x 1 (for drum sound module)
Connection cable
Kick plug: 1/4-inch TRS phone type
Tom 1–4 plugs: 1/4-inch TRS phone type
Crash 1, 2 plugs: 1/4-inch TRS phone type
AUX 1–4 plugs: 1/4-inch TRS phone type (Pad side: female plug)
Weight
21 kg
39 lbs 8 oz
(including connection cables)
Accessories
Cable tie x 4
Owner’s Manual (DTS-30S, DBS-30/DCS-30, PDS-20)
* This document explains the specifications of the product at the time that the document
was issued. For the latest information, refer to the Roland website.
CAUTION
Route all power cords and cables in such a way as to prevent them from getting
entangled
Injury could result if someone were to trip on a cable and cause the unit to fall or
topple.
Disconnect all cords/cables before moving the unit
Damage or malfunction may result if you fail to disconnect all cables before
moving the unit.