Whelen I06UF4P - Manual (Page 2)

Page 2
NOTE: Passenger-side Charger mounting
kit components are shown here for
reference. Other models will mount
the same. NOTE:
NOTE:
NOTE:
Slide bracket under passenger
side visor swivel bracket
Secure bracket
under visor clip
Mount to
bottom of
housing
Secure rubber seal to
leading edge and side
panel of lightbar.
#10 External
tooth lock
washer
10-24
Acorn Nut
Lightbar
Side View
Sheet metal screw (from lightbar)
#10 External tooth
lock washer
#10 Flat washer
Mounting brackets
Wiring Diagram
WHT/GRN
BROWN
WHT/BLK
BLUE
ORANGE
WHT/ORG
BLK
RED Scan-Lock
Ground (-)
Low Power
Take-Downs
TD / Flash
Flash
Steady
Momentary Switch
SPST Switch
SPST Switch
SPST Switch
SPST Switch
SPST Switch
+12VDC
All Fuses & Switches
Customer Supplied
Fuse @ 15 AMPS
LINZ6™ Models
TIR3™ Models
Fuse @ 10 AMPS
Wire Color Function
1 AMP Fuse
BATTERY
IMPORTANT AIR BAG WARNING! Do not install this product or route any
wires in the deployment area of your air bag. Equipment mounted or
located in the air bag deployment area will damage or reduce the
effectiveness of the air bag, or become a projectile that could cause serious
personal injury or death. Refer to your vehicle owners manual for the air
bag deployment area. The User/Installer assumes full responsibility to
determine proper mounting location, based on providing ultimate safety to
all passengers.
Installation / Split Bar:
IMPORTANT! The lightbar should be located a minimum of 16" from
any radio antennas!
Note: When routing the wires, it is important to choose a path that will
keep the wires away from excessive heat or any vehicle equipment that
could compromise the integrity of the wires (ex. trunk lids, door jams, etc.)
1.
Locate and install the rubber window seal (included) onto the lower, leading
edge and side of the housing.
2. Using an appropriately sized Torx head screwdriver, loosen (do not remove)
the three screws securing the passenger-side visor swivel bracket to the
vehicle.
3. Remove the screws securing the visor clip to the vehicle. Remove and
retain the clip and all hardware.
4. Locate the
passenger-side
mounting bracket
(indicated with a “P”)
and orient as shown.
5. Slide mounting
bracket fingers
between loosened
swivel bracket and
headliner. The bracket
fingers should straddle the inner
section of the swivel bracket when
properly oriented.
6. Position the keyed opening of the mounting bracket directly under the
mounting location for the visor clip removed in step 2. With the bracket in
this position, remount the visor clip in its original location using the original
hardware.
7. Firmly tighten any hardware loosened in this procedure.
8. Repeat this procedure for the driver-side assembly and mounting bracket
(indicated with a “D”).
9. Position the lightbar as shown. Using the hardware provided, secure the
lightbar to the mounting bracket.
10. When properly mounted, the rubber seal will be in full contact with the
vehicle windshield and roof. This is to prevent light output from entering the
passenger compartment. When this has been achieved, tighten mounting
hardware firmly to maintain contact.
11. Route the lightbar cable down the vehicle A-pillar to your control head.
12. Make all wiring connections using the information in the wiring diagram.
Wiring:
WARNING! All customer supplied wires that connect to the positive terminal of
the battery must be sized to supply at least 125% of the maximum operating
current and FUSED at the battery to carry that load. DO NOT USE CIRCUIT
BREAKERS WITH THIS PRODUCT!
Operation:
This lightbar is powered and controlled by an 8-conductor cable exiting the
lightbar. All functions listed here are not present in all lightbars.
White/Green - Scan-Lock™
The WHITE/GREEN wire allows you to choose from the available flash
patterns listed below. First you must activate the lighthead(s) you wish to
change:
TO CYCLE THROUGH ALL PATTERNS: Apply +12 VDC to the WHITE/GREEN
wire for less than 1 second and release to cycle forward. Apply +12 VDC to the
WHITE/GREEN wire for more than 1 second and release to cycle backward.
TO SET A PATTERN AS DEFAULT: When the pattern is displayed, allow it to run
for more than 5 seconds. The lighthead will now display this pattern when active.
TO RESET TO THE FACTORY DEFAULT PATTERN: Turn off power and apply
+12 VDC to the WHITE/GREEN wire while turning power on.
Use a normally open momentary switch to control Scan-Lock.
Brown: Hi/Low Power
The low power feature allows you to step the lightbar down to run in low
power for night time use. Fuse this wire @ 1AMP. A single pole / single
throw switch can be used to control Hi/Low power.
To activate Low power operation: Apply +12 VDC to the BROWN wire.
To restore regular power: Remove the BROWN wire from +12 VDC.
White/Black: Take-Downs
Apply +12 VDC to the WHITE/BLACK wire to activate the take-downs. Fuse this
wire @ 1AMP.
Blue: Take-Down Flasher
Apply +12 VDC to the BLUE wire to cause the take-downs to flash. Fuse this wire
@ 1AMP.
White/Orange: Steady-burn option
Apply +12 VDC to the WHITE/ORANGE wire to activate the center steady-burn
lighthead(s). Fuse this wire @ 1AMP.
Orange: Flasher
Apply +12 VDC to the ORANGE wire and all of the lightheads that are activated
will flash. Fuse this wire @ 1AMP.
IMPORTANT! Before returning this vehicle to active service, visually
confirm the proper operation of this product, as well as all vehicle
components/equipment.
Available Flash Patterns:
1. SignalAlert™ 75 Alternating
2. SignalAlert™ 75 In-Out
3. SignalAlert™ 75 Left-Right
4. SingleFlash 90 Alternating
5. SingleFlash 90 In-Out
6. SingleFlash 90 Left-Right
7. CometFlash® 75 Alternating
8. CometFlash® 75 In-Out
9. CometFlash® 75 Left-Right
10.SingleFlash 75 Alternating
11. SingleFlash 75 In-Out
12.SingleFlash 75 Left-Right 13. SingleFlash 150 Alternating
14. SingleFlash 150 In-Out
15. SingleFlash 150 Left-Right
16. DoubleFlash 75 Alternating
17. DoubleFlash 75 In-Out
18. DoubleFlash 75 Left-Right
19. ActionFlash™ Alternating
20. ActionFlash™ In-Out
21. ActionFlash™ Left-Right
22. ActionScan™ Alternating
23. ActionScan™ In-Out
24. ActionScan™ Alternating.