Whelen SAK11 - Manual (Page 2)

Page 2
1/4
(Speaker & Bracket)
- 20 X 1-1/2"
HEX HEAD SS
1/4" SPLIT
L O C K
WASHER
1/4" SPLIT
L O C K
WASHER
1/4 X 20 X 1-1/4
H E X H E A D
(Speaker Only)
1/4
(Speaker & Bracket)
- 20 X 1-1/2"
HEX HEAD SS
1/4" SPLIT
L O C K
WASHER
1/4" SPLIT
L O C K
WASHER
1/4 X 20 X 1-1/4
H E X H E A D
(Speaker Only)
SA315 / Rear View
wire
exit &
drain
hole
A
A
A A
IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and
operation of this product will not interfere with or compromise the operation or efficiency of any vehicle
equipment!
IMPORTANT! Before returning the vehicle to active service, visually confirm the proper operation of this product, as well as all vehicle
components/equipment.
The SA315 siren speaker mounting kit comes with 3 long bolts (1/4-20 X 1-1/2” Hex Head SS). The
longer bolts are necessary to go through the mounting bracket, the siren housing and into the
siren driver. They will replace 3 of the 4 shorter bolts (“A”) that secure the siren driver to the
speaker housing. Your speaker is shipped with 2 of the shorter bolts installed. A short bolt
must be used in the 2 holes that do not go through the bracket so they will properly secure the
driver to the housing. If you need to remove all 4 bolts at once be sure to hold the driver
securely in place.
IMPORTANT: For drainage purposes, the speaker must be oriented so that the wire
passage hole is in the “6 o’clock” position (closest to the road).This is also the
drain hole for the siren. Improper mounting will result in premature driver failure
and void the product warranty.
SA315 / Rear View
wire
exit &
drain
hole
A
A
A A
IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and
operation of this product will not interfere with or compromise the operation or efficiency of any vehicle
equipment!
IMPORTANT! Before returning the vehicle to active service, visually confirm the proper operation of this product, as well as all vehicle
components/equipment.
The SA315 siren speaker mounting kit comes with 3 long bolts (1/4-20 X 1-1/2” Hex Head SS). The
longer bolts are necessary to go through the mounting bracket, the siren housing and into the
siren driver. They will replace 3 of the 4 shorter bolts (“A”) that secure the siren driver to the
speaker housing. Your speaker is shipped with 2 of the shorter bolts installed. A short bolt
must be used in the 2 holes that do not go through the bracket so they will properly secure the
driver to the housing. If you need to remove all 4 bolts at once be sure to hold the driver
securely in place.
IMPORTANT: For drainage purposes, the speaker must be oriented so that the wire
passage hole is in the “6 o’clock” position (closest to the road).This is also the
drain hole for the siren. Improper mounting will result in premature driver failure
and void the product warranty.
IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any vehicle equipment! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well as all vehicle components and equipment.
IMPORTANT! It is the responsibility of the installation technician to make sure that the installation and operation of this product will not
interfere with or compromise the operation or efficiency of any vehicle equipment! Before returning the vehicle to active service,
visually confirm the proper operation of this product, as well as all vehicle components and equipment.
DANGER!
Sirens produces extremely loud emergency warning tones! Exposure to these tones without proper and adequate hearing
protection, could cause ear damage and/or hearing loss! The Occupational Safety & Health Administration (www.osha.gov) provides
information necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95. Until you have determined the safe
exposure times for your specific application, operators and anyone else in the immediate vicinity should be required to wear an approved
hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!
DANGER!
Sirens produces extremely loud emergency warning tones! Exposure to these tones without proper and adequate hearing
protection, could cause ear damage and/or hearing loss! The Occupational Safety & Health Administration (www.osha.gov) provides
information necessary to determine safe exposure times in Occupational Noise Exposure Section 1910.95. Until you have determined the safe
exposure times for your specific application, operators and anyone else in the immediate vicinity should be required to wear an approved
hearing protection device. FAILURE TO FOLLOW THIS RECOMMENDATION COULD CAUSE HEARING LOSS!