Whelen SABKT24 - Manual

Page 1
RADIATOR
RADIA
TO
R
SUPPORT
RADIA
TO
R
SUPPORT
Drill out existing hole & use
supplied 1/4" - 20 riv nut.
Use existing hardware
and mounting hole.
RADIATOR
Fig. 2
RADIA
TO
R
SUPPORT
RADIATOR
RADIA
TO
R
SUPPORT
RADIA
TO
R
SUPPORT
Drill out existing hole & use
supplied 1/4" - 20 riv nut.
Use existing hardware
and mounting hole.
RADIATOR
Fig. 2
RADIA
TO
R
SUPPORT
©2007 Whelen Engineering Company Inc.
Form No.14094B (121508)
Installation Guide:
SA314 Siren Speaker Bracket
2007 Suburban / Tahoe / SABKT24
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Au
to
mo
tiv
e:
Sirens & Switches
14 X 1"
PPHSMS
INT. TOOTH
SPLIT LOCK
WASHER
Fig. 3
Installation:
1. Open the hood and remove the protective cover from
the front of the engine compartment (Fig. 1). Refer to
the vehicle manual for instructions.
2. Remove the existing bolt (Fig. 2) from the passenger
side radiator support (toward bottom).
IMPORTANT NOTE! This installation uses Rivnuts™ to secure the bracket to the vehicle. This type of hardware requires the
use of a specialized installation tool. Refer to the owners manual included with this
tool for proper installation. Be
sure to follow the mounting hole
specifications precisely!
3.
Drill out the existing hole
(toward the top of the radiator
support) with a .391 drill bit
and install the supplied riv
nut.
4. Secure the siren speaker to
the bracket with the supplied hardware (Fig. 3).
IMPORTANT: For drainage purposes, the speaker must be oriented so
that the wire passage/drain hole is in the “6 o’clock” position (closest
to the road). Improper mounting will result in premature siren driver failure and void the product warranty.
©2007 Whelen Engineering Company Inc.
Form No.14094B (121508)
Installation Guide:
SA314 Siren Speaker Bracket
2007 Suburban / Tahoe / SABKT24
®
ENGINEERING COMPANY INC.
Internet: www.whelen.com
Sales e-mail: [email protected]
Canadian Sales e-mail: [email protected]
Customer Service e-mail: [email protected]
For warranty information regarding this product, visit www.whelen.com/warranty
51 Winthrop Road,
Chester, Connecticut 06412-0684
Phone: (860) 526-9504
Fax: (860) 526-4078
Au
tom
o
tive
:
Sirens & Switches
14 X 1"
PPHSMS
INT. TOOTH
SPLIT LOCK
WASHER
Fig. 3
Installation:
1. Open the hood and remove the protective cover from
the front of the engine compartment (Fig. 1). Refer to
the vehicle manual for instructions.
2. Remove the existing bolt (Fig. 2) from the passenger
side radiator support (toward bottom).
IMPORTANT NOTE! This installation uses Rivnuts™ to secure the bracket to the vehicle. This type of hardware requires the
use of a specialized installation tool. Refer to the owners manual included with this
tool for proper installation. Be
sure to follow the mounting hole
specifications precisely!
3.
Drill out the existing hole
(toward the top of the radiator
support) with a .391 drill bit
and install the supplied riv
nut.
4. Secure the siren speaker to
the bracket with the supplied hardware (Fig. 3).
IMPORTANT: For drainage purposes, the speaker must be oriented so
that the wire passage/drain hole is in the “6 o’clock” position (closest
to the road). Improper mounting will result in premature siren driver failure and void the product warranty.