Powerfix BG 1200 - Manual (Page 2)

Löt- und Gasgeräte GmbH
Bahnhofstraße 50, D-74254 Offenau
Tel. +49 7136 9594-0
Fax +49 7136 9594-44
Internet: www.cfh-gmbh.de
E-Mail: [email protected]
S
tand: VO-01.13
and the bottom of the lower part of the blow torch pointing downwards).
Screw all parts together precisely and without interruption. Do not strip
the screw thread.
Steps to be taken when fitting the butane cartridge:
Close the regulation valve on the upper part (No.1) of the blow torch by
turning it clockwise (-). Place the butane gas cartridge into the cartridge
holder (No.3). Now screw the cartridge holder gastightly to the upper
part (No. 1+3), till the safety latch at the side snaps (No. 1b).
Changing the butane cartridge
It is possible to change the butane cartridge only if it is completely empty
(see section headed Security instructions – Warning). Check that the
cartridge is empty before changing (shake it a little if splashing of liquid
is audible). Make sure the flame on the burner is extinguished before
loosening the cartridge and the burner has cooled down. You can loosen
the lower part (No.3) from the upper part (No.1) by pressing the safety
latch (No. 1b) at the side and rotating the lower part counterclockwise
(No.3). Take the empty butane cartridge from the lower part of the device
and dispose of it accordingly. Now you can attach a new butane cartridge
(see section Attaching the butane cartridge).
How to operate the device
Fit the cartridge properly into the device (see Attaching the butane
cartridge). Carry out a test for leaks (to be carried out outside). Afterwards
turn the gas regulation valve (No. 1a) by about ½ rotation in direction
of the arrow towards (+). Then light the flame at the burner tip and only
now open completely the gas regulation valve (No. 1a), so that the flame
can reach its highest performance. By turning the regulation valve
(No. 1a) in direction towards (+) and (-) you can regulate the performance
of the burner.
Very important!
When starting up the device do not hold it horizontally or with the
bottom pointing upwards and do not shake it. In this case, liquid
gas would stream into the burner. After lighting the burner, let it
preheat at least for 3 minutes, before you turn the blow lamp with
burner head pointing downwards (see No.5). Otherwise there is a
danger that liquid gas would stream into the burner, which would
lead to a blazing uncontrolled flame. However if this happens, the
device has to be immediately positioned upright again, in order to stabilize
and reach its normal intensity. After the recommended preheating time
(appx. 3 mins) the blow lamp is fully functional again.
Switching off the device
By turning the gas regulation valve (No. 1a) in the direction of the arrow
(-) the supply of gas is stopped and the flame extinguishes. Let the
burner cool down.
Storage and transport
Follow the safety instrauctions stated on the butane cartridge.
Storage: Store the device in a vertical position!. Never store the device
or the butane cartridges below ground level (e.g. cellar, boiler room,
etc.). Storing area must be sufficiently ventilated.
Transport: Ensure that the device stands securely upright and is secured
during the transport. Make sure that the device does not fall over or fall
down uncontrollingly.
Care of the device + Repair service
It is allowed to use only recommended spare parts. Do not use a device
where any parts are damaged. Any repairs as well as replacement of
the nozzle can be carried out only by an authorized specialist dealer for
liquid gas or by the manufacturer. In case of a repair contact the
manufacturer at the maintenance address below. The nozzle is marked
with 28 (nozzle No. 28 – corresponds with the nozzle diameter of 0,28
mm). Do not make any modifications to the device.
Warranty
The warranty for this device is 3 years from the date of purchase. The
warranty starts with the date of purchase. Please keep the original receipt
in a safe place. This document is required as a proof of purchase. If any
material or manufacturing defects occur within 3 years from the date of
purchase of this product, the product will - at our discretion - be either
repaired or replaced free of charge for you. This guarantee presumes
that you submit the defective device and the proof of purchase (receipt)
together with a short description of the defect and when the defect
occurred within a period of 3 years. In case that the defect is covered
by our warranty, you will receive either the repaired product or a new
one. In case of a warranty claim, please get in touch with us by E-Mail
under [email protected]. We will contact you immediately.
Changing the gasket
When changing the gasket the wider lower rim of the new gasket must
fit precisely to the gasket holder on the piercing pin. The rubber gasket
can be replaced only by an authorized specialist dealer or by the
manufacturer.
Cleaning the device
It is possible to clean the device with a dry cloth only when the burner
has cooled down. Do not use any cleansing agents because the oppenings
in the burner and the nozzle could become blocked.
Environmental instructions
The gas used is environment-friendly liquid gas, which does not burden
or damage the environment and it is not dangerous for the ozone layer.
The butane cartridge or its contents do not have a restricted shelf-life.
Follow the regulations for the liquid gas.
Disposal of the butane cartridge
Totally emptied butane cartridges must be disposed of by using the Dual
recycling system. Butane cartridges, which are not completely empty,
have to be disposed of at collection centres for harmful substances.
Disposal of the device
The device is produced of recyclable materials. To dispose of or to
recycle this device, get in touch with an authorized local Recycling Office
or a waste disposal company.
Technical data
Gas type: butane, unregulated, in a pressure
gas cartridge
Filling capacity of the cartridge: 190 g
Category: vapour pressure butane (I
3
)
Consumption: appx. 145 g/h
Performance: appx. 2,0 kW
Working temperature: appx. 650°C
Burner: P 21
Nozzle: Ø 0,28 mm
The performance in the operating manual applies to measurement results
with test gas under test conditions. When using the provided butane
cartridge under normal conditions, deviations in the related heat input
can occur. (Important information: The ambient temperature has an
essential influence on the performance of the device. As a general
rule is that the performance decreases at low temperatures).
Technical and optical parameters subject to change
Status: 01/2013
Maintenance address and manufacturer: