Sealey SSC12710 - Manual (Page 11)

 WARNING! Ensure that you have read, understood and
apply Section 1 safety instructions.
7.1. MAINTENANCE SCHEdULE TAbLE.
7.1.1. before performing any jobs within the sound-proof
cabinet, ensure that: The main line switch is turned off
(position “0”) The compressor is disconnected from the
compressed air system and all the pressure has been
released from the compressor and internal pneumatic
circuit.
7.1.2. Weekly: it is advisable to inspect the compressor, paying
special attention to oil leaks and scale due to settled dust and
oil.
7.1.3. Note! If the compressor is used for more than 3000 hours/
year the tasks indicated below are to be performed more
frequently.
7. COMPRESSOR MAINTENANCE
Interval
(hours)
TASKS TO bE PERFORMEd
See
section
Weekly
check if the filters of the electric cabinet are clogged
check if the anti-dust pre-filter is clogged
7.8
Drain condensate on a weekly basis.
500
hours
after
first
start
change oil and oil filter. 7.2
& 7.3
check the electrical connections and tighten if necessary
every
2500
hours or
at least
every
year
replace the oil filter cartridge 7.3
replace the oil separator filter cartridge 7.4
replace the air filter cartridge 7..5
check the transmission 7.6
clean the air/oil radiator. 7.9
check filters in electrical cabinet and replace if
necessary
clean inverter dissipator (if equipped)
check the safety valve
check the electrical connections and tighten if necessary
change oil
7.2
every
7500
hours
check the hydraulic seals
overhaul the suction valve
every
12500
hours
check the hoses and replace if necessary
overhaul oil separator flange
Grease the minimum pressure valve
replace fluorflon pipes 6x4 and 10x10
replace the screw oil seal
replace the screw oil seal
replace the bearings of the radiator fan motor (to be
done by service centre).
replace the delivery or flange
clean the compressor externally when not in use
every
20000
hours
replace inverter fan (if equipped)
replace the bearings of the screw (to be done by
technical service centre)
7.2 CHANGING THE OIL.
7.2.1 change the oil following the initial 500 hours of use and then
every 2500 hours thereafter, or at least once a year.
In case of infrequent use (only a few hours of duty per
day) you should change the oil every 6 months.
7.2.2 referring to fig.14 identify the oil filler cap (1) and the oil drain
tap (2). unscrew the oil filler cap (1) and put to one side.
Ensure that the oil drain tap is shut off (i.e. tap handle at 90° to
the body of the tap). Have to hand a pipe and container ready
to collect the oil.
7.2.3. unscrew the hex nut from the end of the oil drain tap. screw in
the tail piece attachment supplied with the compressor. Push
the pipe onto the tailpiece and ensure that the other end is in
the collection container. open the drain tap fig.14-2. once
emptied, close tap, remove the tail piece attachment and
screw the hex nut (with seal) back into place.
7.2.4. fill-up with oil as shown in fig.15 until the level is halfway up
the sight glass. see fig.15-3. screw oil filler cap (1), with its
seal, back into the oil filler hole.
7.2.5. once the oil and oil filter have been changed follow the initial
start up procedure by pressing the stArt & stoP buttons on
and off for 3 or 4 seconds to start the machine intermittently.
After this, leave the compressor to run for roughly 5 minutes
then turn it off and check the oil level again. Check the oil
level once a month.
7.2.6. never mix different types of oil, therefore always ensure that
the circuit is completely empty before filling-up with oil. Each
time the oil is changed the filter is also to be replaced.
fig.15
Original Language Version
fig.14
7.2.7. Recommended oil.
mineral oil : Grade 46st
Part No. Qty. description
scPo1s 1ltr mineral oil.
scPo5 5ltr mineral oil.
ssc12710 & ssc12710D Issue: 3 - 23/02/12