Sealey SAC05020 - Manual

InstructIons for: COMPRESSOR
50ltr bElt DRIVE 2.0hp OIl FREE
model no:
SAC05020
thank you for purchasing a sealey product. manufactured to a high standard this product will, if used according to these instructions
and properly maintained, give you years of trouble free performance.
IMPORTANT: PlEASE READ tHESE INStRUCtIONS CAREFUllY. NOtE tHE SAFE OPERAtIONAl REQUIREMENtS, WARNINGS & CAUtIONS.
USE tHE PRODUCt CORRECtlY AND WItH CARE FOR tHE PURPOSE FOR WHICH It IS INtENDED. FAIlURE tO DO SO MAY CAUSE
DAMAGE OR PERSONAl INJURY AND WIll INVAlIDAtE tHE WARRANtY. PlEASE KEEP INStRUCtIONS SAFE FOR FUtURE USE.
1.2. GENERAl SAFEtY INStRUCtIONS

familiarise yourself with the application and limitations of the compressor.
 ensure the compressor is in good order and condition before use. If in any doubt do not use the unit and contact an electrician/service
agent.
 WARNING! Compressor must only be serviced by an authorised agent. DO NOT tamper with, or attempt to adjust, pressure
switch or safety valve.
 Before moving, or maintaining the compressor ensure it is unplugged from the mains supply and that the air tank pressure has been
vented.
 only use recommended attachments and parts. to use unapproved items may be dangerous and will invalidate your warranty.
 read the instructions regarding any accessory used with the compressor. ensure the safe working pressure of any air appliance used
exceeds unit’s output pressure. If using spray gun, check that the area selected for spraying is provided with air change system/ventilation.
 ensure the air supply valve is turned off before disconnecting the air supply hose.
 to move the compressor use the handle only.
 DO NOt attempt to lift or move the compressor by any means other than by the handle.
 use the compressor in a well ventilated area with a temperature above 5°c, and ensure it is placed on a firm, level surface.
 Keep tools and other items away from the compressor when it is in use, and keep area clean and clear of unnecessary items.
 ensure any air hose attached is not tangled, twisted or pinched.
 Keep children and unauthorised persons away from the working area.
 DO NOt dis-assemble compressor for any reason. the unit must be checked by qualified personnel only.
 DO NOt use the compressor outdoors, or in damp, or wet, locations and DO NOt operate within the vicinity of flammable liquids,
gases or solids.
 DO NOt touch compressor cylinder, cylinder head or pipe from head to tank as these may be hot and will remain so for some time
after shutdown.
1.1. ElECtRICAl SAFEtY
 WARNING! It is the responsibility of the owner and the operator to read, understand and comply with the following:
You must check all electrical products, before use, to ensure that they are safe. You must inspect power cables, plugs, sockets and
any other connectors for wear or damage. You must ensure that the risk of electric shock is minimised by the installation of
appropriate safety devices. A residual current circuit Breaker (rccB) should be incorporated in the main distribution board. We also
recommend that a residual current device (rcd) is used. It is particularly important to use an rcd with portable products that are
plugged into a supply which is not protected by an rccB. If in any doubt consult a qualified electrician. You may obtain a residual
current device by contacting your sealey dealer.
You must also read and understand the following instructions concerning electrical safety.
1.1.1. the electricity at Work Act 1989 requires that all portable electrical appliances, if used on business premises, are tested by a qualified
electrician, using a Portable Appliance tester (PAt), at least once a year.
1.1.2. the Health & safety at Work Act 1974 makes owners of electrical appliances responsible for the safe condition of those appliances
and the safety of the appliance operators. If in any doubt about electrical safety, contact a qualified electrician.
1.1.3. ensure that the insulation on all cables and on the appliance is safe before connecting it to the power supply. see 1.1.1. and 1.1.2.
and use a Portable Appliance tester.
1.1.4. ensure that cables are always protected against short circuit and overload.
1.1.5. regularly inspect power supply cables and plugs for wear or damage and check all
connections to ensure that none are loose.
1.1.6. Important: ensure that the voltage marked on the appliance matches the power supply
to be used and that the plug is fitted with the correct fuse - see fuse rating at right.
1.1.7. DO NOt pull or carry the appliance by the power cable.
1.1.8. DO NOt pull the plug from the socket by the cable.
1.1.9. DO NOt use worn or damaged cables, plugs or connectors. Immediately have any faulty
item repaired or replaced by a qualified electrician. When a Bs 1363/A uK 3 pin plug is
damaged, cut the cable just above the plug and dispose of the plug safely.
fit a new plug according to the following instructions (uK only).
a) Connect the GREEN/YEllOW earth wire to the earth terminal ‘E’.
b) Connect the bROWN live wire to the live terminal ‘l’.
c) Connect the blUE neutral wire to the neutral terminal ‘N’.
d) After wiring, check that there are no bare wires, that all wires have been correctly
connected, that the cable outer insulation extends beyond the cable restraint and that the restraint is tight.
double insulated products, which are always marked with this symbol , are fitted with live (brown) and neutral (blue) wires only.
to rewire, connect the wires as indicated above - do not connect either wire to the earth terminal.
1.1.10. Products which require more than 13 amps are supplied without a plug. In this case you must contact a qualified electrician to ensure
that a suitably rated supply is available. We recommend that you discuss the installation of an industrial round pin plug and socket
with your electrician.
1.1.11. If an extension reel is used it should be fully unwound before connection. A reel with an rcd fitted is preferred since any appliance
plugged into it will be protected. the cable core section is important and should be at least 1.5mm², but to be absolutely sure that the
capacity of the reel is suitable for this product and for others which may be used in the other output sockets, we recommend the use
of 2.5mm² section cable.
1. SAFEtY INStRUCtIONS
RECOMMENDED
FUSE RAtING 13 AMP
Blue
Neutral
Wire
Yellow & Green
Earth Wire
Cable
Restraint
Brown
Live
Wire
Original Language Version sAc05020 Issue: 2 - 21/10/11