Sealey SNA9821 - Manual

Page. 1
 WARNING! Isolate the drill from the electrical supply before connecting or disconnecting nibbler
attachment.

Ensure all safety instructions supplied with the drill to be used, are adhered too, in addition to these
safety instructions.

Maintain the nibbler attachment in good condition.
 Replace or repair damaged parts. Use recommended parts only. Unauthorised parts may be
dangerous and will invalidate the warranty.
 Maintain correct balance and footing. Ensure that the floor is not slippery and wear non-slip shoes.
 Keep children and unauthorised persons away from the work area.
 Evaluate the work area before using the attachment.
 Secure loose workpieces with a clamp, vice or other adequate holding device. DO NOT hold
workpiece in your hand.

Avoid unintentional starting of the drill.

Wear approved safety eye protection (standard spectacles are not adequate).

Remove ill fitting clothing. Remove ties, watches, rings, any loose jewellery and contain long hair.

DO NOT use the nibbler attachment where there are flammable liquids, solids or gases such as paint
solvents, etc.
 DO NOT allow children to operate the nibbler attachment.
 DO NOT operate the nibbler attachment if any parts are missing as this may cause failure or possible
personal injury.
 DO NOT use the nibbler attachment for a task it is not designed to perform.
 DO NOT operate the drill and nibbler attachment when you are tired or under the influence of alcohol,
drugs or intoxicating medication.

DO NOT exceed the capacities shown below, for the material to be cut.

Familiarise yourself with the application and limitations of the nibbler attachment, as well as the
specific hazards.
 When not in use, disconnect from the drill and store in a safe, dry childproof location.
InStRuctIonS FoR:
DRILL NIbbLeR ATTAchmeNT
MoDEL no: sNA9821
thank you for purchasing a Sealey product. Manufactured to a high standard this product will, if used according to these instructions and
properly maintained, give you years of trouble free performance.
1. sAFeTY INsTRUcTIONs
2. specIFIcATION
3. OpeRATION
IMPORTANT: pLeAse ReAD These INsTRUcTIONs cAReFULLY. NOTe The sAFe OpeRATIONAL ReQUIRemeNTs, WARNINGs & cAUTIONs. Use The pRODUcT
cORRecTLY AND WITh cARe FOR The pURpOse FOR WhIch IT Is INTeNDeD. FAILURe TO DO sO mAY cAUse DAmAGe AND/OR peRsONAL INJURY AND WILL
INVALIDATe The WARRANTY. pLeAse Keep These INsTRUcTIONs sAFe FOR FUTURe Use.
turns an electric or air drill into a versatile nibbler suitable for cutting intricate
shapes in various materials. Double-ended punch allows handle to be removed
and re-attached to opposite side, for longer periods of use.
Maximum Speed: . . . . . . . . . . . . . . 3000RPM
Maximum capacity: . . . . . . . . . . . . Steel: . . . . . . . . . . . . . . . . . .1.6mm
Stainless Steel: . . . . . . . . . .1.2mm
Brass, Plastic, copper: . . . .2.0mm
Replacement Punch: . . . . . . . . . . . SnA9821P
Replacement Die:. . . . . . . . . . . . . . SnA9821D
3.1. Attach the nibbler to a suitable drill by inserting the drive into the drill chuck and tightening the chuck.
3.2. Attach handle to the nibbler as shown (fig.1).
3.3. Secure the workpiece in a suitable clamp or vice, ensuring there is at least a 15mm clearance
underneath the area of material to be cut.
3.4. Plug the drill into the supply, first ensuring it is turned off.
3.5. Securely hold the nibbler attachment handle and the drill, switch the drill on.
3.6. carefully move the nibbler attachment towards the starting point of the desired cut and engage
nibbler head with the material, start to cut into the material.
3.7. carry on cutting through the material as desired, keeping the nibbler attachment at a right angle to the
material. When finished cutting, move the nibbler head away from the material before switching off the
drill.
Original Language Version
SnA9821 Issue: 1 - 29/01/10