Sealey AK435 - Manual (Page 3)

3.2. CHANGING THE BATTERY

WARNING! Ensure you read, understand and apply safety instructions
relating to the battery before changing.
1. Undo the spotlight hood (fig.1-H) by turning it anti-clockwise.
2. Carefully lift the hood and reflector assembly. Lay the hood and glass to
one side.
3. Remove the 4 screws holding the inner plastic chassis (fig.6-1) and
carefully lift out the chassis.
4. First disconnect the black negative wire from the battery (fig.6-2).
5. Then disconnect the red positive wire from the battery (fig.6-3).
 WARNING! Beware of causing a short circuit.
6. Carefully remove the battery.
7. Replace with genuine Sealey battery and install by reversing the
above procedure.
NOTE: Take care not to pinch or misconnect any wires.
8. Dispose of old battery in accordance with local authority battery
regulations. DO NOT dispose of with regular refuse.
3.1. CHANGING THE SPOTLIGHT BULB
 WARNING! Ensure the spotlight is turned off and the lens has cooled prior
to changing the bulb.
1. Undo the spotlight hood (fig.1-H) by turning it anti-clockwise.
2. Carefully lift out the reflector assembly and lay it face down as in fig.5.
3. Remove the screw and nut (fig.5-1) that secures the black wire.
4. Remove the spring clip (fig.5-2) that holds the bulb in place and lift out
the bulb (fig.5-3).
5. Slide the insulation sleeve that covers the bulb cable connector onto the
red cable (fig.5-4). If the sleeve is fixed with ties, remove these first.
6. Undo the bulb cable connector and dispose of the old bulb and cable in
accordance with local authority regulations.
7. Hold the new bulb with a lint free cloth, (do not handle the bulb), and
install by reversing the above procedure.
8. Ensure that you slide the insulation sleeve (fig.5-4) back over the bulb
cable connector.
 WARNING! Beware of causing a short circuit.
3. MAINTENANCE
4. PARTS
Environmental Protection.
Recycle unwanted materials instead of disposing of them as waste.
All tools, accessories and packaging should be sorted, taken to a recycle centre and disposed of in a manner which is compatible with the environment.
When the product is no longer required, it must be disposed of in an environmentally protective way. Contact your local solid waste authority for
recycling information.
Battery Removal.
 WARNING! Ensure the spotlight is turned off before removing the battery Refer to Section 3.2 to remove the battery.
Dispose of batteries according to local authority guidelines.
Under the Waste Batteries and Accumulators Regulations 2009, Jack Sealey Ltd are required to inform potential purchasers of products containing batteries
(as defined within these regulations), that they are registered with Valpak’s registered compliance scheme.
Jack Sealey Ltd’s Batteries Producer Registration Number (BPRN) is BPRN00705
NOTE: It is our policy to continually improve products and as such we reserve the right to alter data, specifications and component parts without prior notice.
IMPORTANT: No liability is accepted for incorrect use of this product.
WARRANTY: Guarantee is 12 months from purchase date, proof of which will be required for any claim.
INFORMATION: For a copy of our latest catalogue and promotions call us on 01284 757525 and leave your full name and address, including postcode.
01284 757500
01284 703534 [email protected]
Sole UK Distributor, Sealey Group,
Kempson Way, Suffolk Business Park ,
Bury St. Edmunds, Suffolk,
IP32 7AR
www.sealey.co.uk
Web
email
Original Language Version
fig.6
fig.5
AK435.V3 Issue: 1 - 07/03/11
PARTS DESCRIPTION
AK436.V3-01 BULB HALOGEN H3 6V 55W
AK436.V3-02 MAINS CHARGER 9V 300mA
AK436.V3-03 BATTERY
AK436.V3-04 SWITCH (SW-3)
AK436.V3-05 CIGARETTE LIGHTER LEAD