Miomare VS3L - Manual (Page 12)

15 GB / MT
Service
If you have any queries, please contact our service office.
Here you will receive all necessary information regard-
ing service questions such as returns, etc.
� 00800/01928321
Ravak a.s.
Obecnicka 285
26181 Příbram 1, ČR
Declaration of conformity
This product satisfies the requirements of the valid European and
national directives
Its conformity has been verified. The appropriate declarations
and documents are retained by the manufacturer.
Ravak a.s., Obecnicka 285, 26181 Příbram 1, ČR
05
EN 14428
Folding bathtub screen/
shower screen with plastic panels
Cleanability: passed
Breaking properties: passed
Durability: passed
Warranty / Service
BA_Faltw_Kö469_content.indd 15 23.09.2005 15:50:48 Uhr
fit correctly. The broad drain-off lips must point towards the
bathtub.
See Fig. G:
• Level out any uneven areas between the wall connection
profile and the edge of the bath with silicone.
• Insert the folding bathtub screen fully in the wall connection
profile. Take care that it is installed correctly – the smooth
side of the plastic panel must be on the inside / the rough
side of the plastic panel on the outside.
• Guide the 3 fastening screws T with the 3 washers Y
through the outer folding screen element.
• Screw the 3 fastening screws gently into the thread of the
wall connection profile – do not screw them tight.
See Fig. H:
• Open the folding screen fully along the edge of the bath.
• Position the folding screen so that the lower plastic seals
are lying exactly parallel on the edge of the bath.
• Screw the 3 fastening screws with the 3 washers tight into
the screw threads of the outer element.
• Make sure that the folding screen is positioned exactly par-
allel on the edge of the bath when open and flush against
the wall when closed.
• Position the folding screen exactly. If necessary, loosen the
fastening screws and screw them back on after aligning the
folding screen.
See Fig. I:
Note: on smooth walls it is not necessary to use silicone be-
tween the wall connection profile and the wall.
Level out uneven areas with silicone as follows:
• Fill the gaps between the inner and outer side of the wall
connection profile and the wall with silicone along the full
length.
• Fill the gaps between the frame profile of the outer fold-
ing screen elements and the wall connection profile with
silicone to a height of 100 mm.
Before you can use the folding bathtub screen, the silicone filling
must have set completely. Please observe the manufacturer's
information with regard to the setting time of the silicone used.
Use
You can use the folding screen as a splash guard on the bathtub
for showering. You can open out and close the folding screen
from the outside or inside of the bath.
Opening the folding screen
• Open out the folding screen fully so that it runs parallel on
the edge of the bath.
Closing the folding screen
• Close the folding screen so that it is flush against the wall.
Cleaning and maintenance
• The folding bathtub screen requires no maintenance.
• After showering, rinse any remaining care products off the
open folding screen into the bath with water.
• Remove the remaining drops of water from the plastic pan-
els of the folding screen with a standard rubber scraper.
• Remove the remaining drops of water from the wall connec-
tion profile and the frame profiles of the folding screen with
a soft cloth.
• Remove any dirt with a cloth and a standard pH-neutral
cleaning agent.
• Prevent discoloration of and damage to the folding bathtub
screen. Do not use bleaching agents, aggressive cleaning
and scouring agents, solvents or cleaning agents containing
acetone and chlorine for cleaning purposes.
• If you have removed the folding bathtub screen, it should be
kept clean and dry at room temperature in the original pack-
ing.
Disposal
Please dispose of any unwanted packaging material at a local
disposal facility. The recyclable packaging materials have been
selected for their ecologically compatible and disposable proper-
ties.
Please contact your district or city council with regard to pos-
sibilities for disposing of the folding bathtub screen once it has
served its useful life.
In this way you are complying with legal requirements and con-
tributing to protecting the environment.
Warranty / Service
Warranty
This product has a warranty of 2 years from the date of pur-
chase. The product was manufactured with care and inspected
thoroughly before delivery. Please keep your receipt as proof of
purchase.
If you have a claim under the warranty, please call the service
office for your country. This is the only way to ensure that your
device can be sent in free of charge.
This warranty covers material or manufacturing defects only.
Never use the product for any purpose other than that for which
it was intended. Do not carry out any work or modification your-
self, since you will otherwise lose your right to claim under the
warranty. This warranty does not restrict your statutory rights.
Installation Use Cleaning and maintance Disposal Warranty / Service
BA_Faltw_Kö469_content.indd 14 23.09.2005 15:50:47 Uhr
14 GB / MT