Miomare VS3L - Manual (Page 10)

13 GB / MT
poses a risk of fatal accident and injury.
The product must not be used as an aid for getting into the
bathtub. This poses a risk of fatal accident and injury.
Make sure that you do not injure yourself by getting trapped
when using the product. This poses a risk of injury.
Caution:
The product must only be used with the supplied original
parts. Otherwise there is a risk of damage.
Before assembly and initial use of the product, check that
the delivery is complete and undamaged. Otherwise there is
a risk of damage as a result of improper use.
Check before initial use of the product that all components
are assembled in accordance with the instruction manual.
Otherwise there is a risk of damage.
The product must not be used for storage purposes. Other-
wise there is a risk of damage.
Take care not to cause general damage when drilling the
mounting holes in the wall tiles.
Prevent discoloration of and damage to the folding bathtub
screen. Do not use bleaching agents, aggressive cleaning
and scouring agents, solvents or cleaning agents containing
acetone and chlorine for cleaning purposes.
The product must only be repaired by an authorized and
skilled specialist. Otherwise there is a risk of damage and
loss of the warranty.
Installation
Do not damage any gas, electricity, water, oil or telecom-
munication lines when fitting the product on the wall. This
poses a risk of fatal accident and injury.
Check the conditions relating to bathroom installations in
your lease agreement.
• Clear space around bathtub.
• Use masking tape to tape up the areas next to the silicone
filling.
• Smooth the surface of the silicone filling with a mixture of
washing-up liquid dissolved in tap water. Dip the tip of your
finger into the mixture and smooth it over the silicone and
repeat if necessary.
The three opening elements are aligned with the wall connection
profile either for left or right-hand installation. Position the fold-
ing screen as required by turning it by 180°.
You will need the following materials for
installation
· Felt-tip pen
· Pencil
· Tape measure
· Spirit level
· Slotted screw driver
· Hammer drill
· Rock drill with 8 mm diameter
· Moisture-proof silicone, approx. 80 g
· Mixture of: washing-up liquid dissolved in approx. 100 ml
tap water
· Crepe adhesive tape
• Unpack all the parts and check that they are undamaged
and complete.
• Decide on the installation position of the folding screen.
• Make sure when choosing the installation position that
fittings, taps, handles for getting in and out of the bathtub,
sloping ceilings or projecting walls will not hinder opening
and closing of the folding screen.
See Fig. B:
• Screw the 3 fastening screws
T with the 3 washers Y
completely out of the screw threads of the wall connection
profile
R .
• Remove the wall connection profile from the frame profile of
the outside folding screen element.
See Fig. C:
• Hold the wall connection profile together with the spirit level
vertically on the wall. The wall connection profile must be in
the centre of the edge of the bathtub.
• Mark the 3 drill holes on the wall with the felt-tip pen (tiles)
or the pencil (joints).
See Fig. D:
• Drill the 3 holes for mounting the folding bathtub screen.
Use a 8 mm diameter rock drill to do this.
First drill the holes to a depth of approx. 5 mm at slow
speed, then increase the speed and continue drilling to a
depth of approx. 50 mm. Take care that you do not cause
any general damage to the wall material.
• Insert the 3 dowels I flush into the drilled holes.
See Fig. E:
• Screw the wall connection profile with the 3 fastening
screws U in the dowels so that it is tight and flush.
See Fig. F:
The following steps apply to both left and right-hand
installation. See also Fig. A.
•
elements.
• Fit the 3 upper plastic seals W into the groove on the upper
edges of the 3 folding screen elements so that they fit
correctly.
Please note that the plastic seals must be inserted in the
groove with the ends first.
• In the area of the joints (grey plastic cover) make sure that
the seals outside the groove lie straight on the upper or
lower edge.
• Then fit the 3 lower plastic seals E into the groove on the
bottom edges of the 3 folding screen elements so that they
Safety Installation
BA_Faltw_Kö469_content.indd 13 23.09.2005 15:50:47 Uhr
metres shown in Fig. F for the individual folding screen
Choose the plastic seals according to the sizes in mili-
Folding bathtub screen VS3L
Introduction
Please read these operating instructions thoroughly and care-
fully. Open out the pages showing the illustrations and figures.
These instructions are part of this product and contain important
information relating to initial use and handling. Please always
observe all safety instructions.
If you have any questions please contact the service office.
Please keep these instructions in a safe place and pass them on
to anyone else as necessary.
Product description and proper use
The 3-part folding bathtub screen is suitable for wall mounting
and for private use in enclosed bathrooms only. The three folding
elements can be opened out on rectangular acrylic bathtubs,
steel bathtubs, cast iron bathtubs, including hydro massage
bathtubs, to form a plane screen wall. Any other use or modifica-
tion of the product constitutes improper use and poses a serious
risk of accident. The manufacturer is not liable for damage
caused by improper use or incorrect handling of the product.
Delivery scope
Please check immediately after unpacking that the delivery
scope (see also Figure A) is complete and that all the individual
parts are in perfect condition.
1 x folding bathtub screen, 3-part
3 x upper plastic seals
3 x lower plastic seals
3 x steel screws, 4 x 40 mm, stainless
3 x 8 mm diameter dowels
Equipment
The 3-part folding bathtub screen VS3L has the features shown
below.
Q Folding bathtub screen, 3-part
W Upper plastic seals
E Lower plastic seals
R Wall connection profile
T Fastening screws
Y Plain washers
Fastening material
U Steel screws 4 x 40 mm, stainless
I 8 mm diameter dowels
Technical data
Material:
Wall connection profile:
aluminium
Frame profile: aluminium
Panel areas: plastic
Seals: plastic
Dimensions:
Opened:
(w) 1400 x (l) 1270 mm x (d) 30 mm
(incl. seals)
Closed: (w) 1400 x (l) 450 x (d) 72 mm
Glass thickness:
Thickness of aluminium
frame with glass:
14 mm
Depth of wall connection
profile:
30 mm
Weight: approx. 7080 g
Safety
Safety instructions
The following instructions are for your own safety and satisfac-
tion when using the folding bathtub screen. Please note that
non-compliance with these safety instructions can lead to a
serious risk of accident.
Explanation of symbols and terms used:
Dangerous voltage: failure to observe this instruction
endangers life and health.
Failure to observe this instruction endangers property.
Following this advice will help you to achieve optimal
results.
Danger:
Do not leave small children unsupervised with the packag-
ing material. There is a risk of fatal accident by suffocation.
Do not leave children unsupervised with the product. There
is a risk of fatal accident and injury.
Make sure before connecting the hammer drill to the mains
power supply that the mains electricity is 230 V ~ 50 Hz
in accordance with regulations and is equipped with a 16
ampere fuse. There is otherwise a risk of fatal accident by
electric shock. Please also read the operating and safety
instructions for your drill.
Installation must be carried out in dry conditions, protected
from moisture. There is otherwise a risk of fatal accident
and injury.
Do not damage any gas, electricity, water, oil or telecommu-
nication lines when installing the product on the wall. This
Introduction Safety
BA_Faltw_Kö469_content.indd 12 23.09.2005 15:50:47 Uhr
2 mm
12 GB / MT
1 x hexagonal spanner