Kichler 49604 User Manual
Kichler Lighting

1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your home.
Place the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room that
you are working on.
c) Place the wall switch in the “OFF” position. If the fixture to
be replaced has a switch or pull chain, place those in the
“OFF”
position.
2) Slip fixture over post and mark position of mounting holes in
post.
3) Remove fixture from post.
4) Drill 3/16” dia holes in post at positions marked .
5) If fixture is provided with ground wire, connect fixture ground
wire to outlet box ground wire with wire connector. (Not
provided). Never connect ground wire to black or white power
supply wires.
6) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
7) Slip fixture over post and secure in place using provided
screws. Screws should slip into holes drilled in post.
8) Thread short end with hexnut of long threaded pipe into
coupling in center of socket cluster.
9) Insert recommended bulb.
10) Lower glass down and pass hole in bottom of glass over end
of long threaded pipe. Pass hole in bottom of glass over
socket cluster. Carefully place glass into bottom of cage.
11) Pass hole in rubber washer over end of threaded pipe
protruding from top of glass. Pass hole in flat washer over end
of threaded pipe. Screw hexnut onto end of threaded pipe.
(DO NOT over tighten.)
12) Lower top of cage down. Pass hole in top of cage over end of
threaded pipe protruding from top of glass.
13) Pass hole in cap over end of threaded pipe protruding from
top of cage. Set cap on top of cage.
14) Thread lockwasher onto end of threaded pipe protruding
from cap. Tighten washer up against cap.
15) Thread hex coupling onto end of threaded pipe protruding
from cap.
16) Lower first top trim down. Set top trim down on top of fixture.
Pass hole in top trim over coupling on top of fixture.
17) Screw end of short threaded pipe with hexnut into coupling in
center of first top trim piece.
18) Pass hole in scalloped trim piece over end of threaded pipe
protruding from first top trim piece. Set scallped trim piece
down on top of first trim piece.
19) Pass hole in third trim piece over end of threaded pipe
protruding from top of scalloped trim. Set that trim piece down
on top of scalloped trim.
20) Thread finial onto end of threaded pipe protruding from last
trim piece. (DO NOT over tighten.)
Date Issued: 1/2/15
IS-49604-US
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
GLASS
VIDRIO
SCREW
TORNILLO
THREADED PIPE
TUBO ROSCADO
HEX COUPLING
ACOPLAMIENTO
HEXAGONAL
BOTTOM CAGE
JAULA INFERIOR
LONG THREADED PIPE
TUBO ROSCADO LARGO
FINIAL
CAPUCHON
THIRD TOP TRIM PIECE
TERCERA GUARNICIÓN
SUPERIOR
SCALLOPED TOP TRIM
PIECE
GUARNICIÓN FESTONEADA
FIRST TOP TRIM PIECE
PRIMERA GUARNICIÓN
SUPERIOR
TOP CAGE
JAULA SUPERIOR
LOCKWASHER
ARANDELA DE
SEGURIDAD
RUBBER WASHER
ARANDELA DE
CAUCHO
FLAT WASHER
ARANDELA PLANA
HEXNUT
TUERCA HEXAGONAL
CAP
TAPA