Kichler 49582 User Manual
Kichler Lighting

1) To install glass panels: Carefully insert glass panel inside
cage. Fit top edge of glass panel into channel along top
inside of cage. Press glass panel up against inside of cage.
Place bracket inside cage. Align hole in step of bracket with
hole in bottom edge of cage. Thread screw up through hole
in bracket and into hole in cage. Tighten screw to secure
bracket and glass panel in place. (See FIG. 2 for glass panel
installation detail.) Repeat these steps for remaining glass
panels.
2) Pass fixture wire from top of fixture through hole in top trim.
Lower top trim down. Set top trim down on top of fixture.
Align hole in top trim with hole in coupling on top of fixture.
3) Pass fixture wire through threaded pipe. Pass end of threaded
pipe through hole in top trim. Screw end of threaded pipe
into coupling.
4) Pass fixture wire through hole in bottom of loop. Thread loop
onto end of threaded pipe protruding from top trim.
5) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
6) Take threaded pipe from parts bag and screw in screw collar
loop a minimum of 6 mm (1/4”). Lock into place with hexnut.
7) Run another hexnut down threaded pipe almost touching
first hexnut. Now screw threaded pipe into mounting strap.
Mounting strap must be positioned with extruded thread
faced into outlet box. Threaded pipe must protrude out the
back of mounting strap. Screw third hexnut onto end of
threaded pipe protruding from back of mounting strap.
8) Connect mounting strap to outlet box.
9) Unscrew the threaded ring from screw collar loop. Take
canopy and pass over screw collar loop. Approximately one
half of the screw collar loop exterior threads should be
exposed. Adjust screw collar loop by turning assembly up or
down in mounting strap. Remove canopy.
10) After desired position is found, tighten both top and bottom
hexnuts up against the bottom and top of the mounting
strap.
11) Slip canopy over screw collar loop and thread on threaded
ring. Attach chain (with fixture connected) to bottom of
screw collar loop. Unscrew threaded ring, let canopy and
threaded ring slip down.
12) Weave electrical wire and ground wire through chain links no
more than 3 inches apart. Pass wire through threaded ring,
canopy, screw collar loop, threaded pipe and into outlet box.
13) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a
hole and two raised dimples. Wrap ground wire from
outlet box around green ground screw, and thread into
hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector
(not provided.) after following the above steps. Never
connect ground wire to black or white power supply wires.
Date Issued: 9/5/14
IS-49582–-US
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
SCREW COLLAR LOOP
OJAL DE COLLAR
ROSCADO
THREADED RING
ANILLO ROSCADO
LOOP
ANILLO
HEXNUT
TUERCA
HEXAGONAL
THREADED PIPE
TUBO ROSCADO
CAGE
JAULA
GLASS PANEL
PANEL DE CRISTAL
ROOF
TECHO
14) Make wire connections (connectors not provided). Reference
chart below for correct connections and wire accordingly.
15) Raise canopy to ceiling.
16) Secure canopy in place by tightening threaded ring onto
screw collar loop.
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
GLASS PANEL INSTALLATION DETAIL
DETALLE DE INSTALACIÓN DEL PANEL DE VIDRIO
BRACKET
SOPORTE
SCREW
TORNILLO
THREADED PIPE
TUBO ROSCADO
TOP TRIM
ADORNO SUPERIOR
COUPLING
ACOPLAMIENTO