Kichler 49601 User Manual
We’re here to help

1) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work
without shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your
home. Place the main power switch in the “OFF”
position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker
switch(s), that control the power to the fixture or room
that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture
to be replaced has a switch or pull chain, place those in
the “OFF” position.
2) Find the appropriate threaded holes on mounting strap.
Assemble mounting screws into threaded holes.
3) Attach mounting strap to outlet box. (Screws not provided).
Mounting strap can be adjusted to suit position of fixture.
4) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole
and two raise dimples. Wrap ground wire from outlet
box around green ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach
ground wire from outlet box under cupped washer and
green ground screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture
ground wire to outlet box ground wire with wire connector.
(Not provided.) After following the above steps. Never connect
ground wire to black or white power supply wires.
5) Make wire connections (connectors not provided.) Reference
chart below for correct connections and wire accordingly.
6) Push fixture to wall, carefully passing mounting screws
through holes in fixture.
7) Screw threaded balls onto mounting screws. Tighten
threaded balls to secure fixture to wall.
8) Insert recommended bulbs.
9) Raise glass up to fixture. Pass hole in top of glass over
threaded pipe on bottom of socket cluster.
10) Fit glass inside top of cage on fixture. Pass hole in bottom of
glass over end of threaded pipe on bottom of socket cluster.
11) Pass hole in rubber washer over end of threaded pipe
protruding from bottom of glass. Pass hole in flat washer
over end of threaded pipe. Screw hexnut onto end of
threaded pipe. (DO NOT over tighten.)
12) Raise bottom of cage up to fixture. Fit bottom of cage over
glass. Pass hole in bottom of cage over end of threaded
pipe protruding from bottom of glass.
13) Thread hex coupling onto end of threaded pipe protruding
from bottom of cage.
14) Thread end of short threaded pipe into hex coupling
protruding from bottom of cage.
15) Pass hole in bottom trim over end of short threaded pipe.
16) Thread finial onto end of short threaded pipe. Tighten finial
to secure cage in place.
Date Issued: 1/2/15
IS-49601-US
MOUNTING STRAP
PLANCHA PARA
MONTAR
GREEN GROUND
SCREW
CUPPED
WASHER
A
B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black
White
*Parallel cord (round & smooth)
*Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
THREADED BALL
BOLA ROSCADO
We’re here to help
866-558-5706
Hrs: M-F 9am to 5pm EST
BOTTOM CAGE
JAULA INFERIOR
GLASS
VIDRIO
THREADED PIPE
TUBO ROSCADO
SHORT THREADED PIPE WITH
HEX COUPLING
TUBO ROSCADO CORTO CON
ACOPLAMIENTO HEXAGONAL
BOTTOM TRIM
GUARNICIÓN INFERIOR
FINIAL
CAPUCHON
SOCKET CLUSTER
GRUPO DE PORTALÁMPARAS
TOP CAGE
JAULA SUPERIOR
RUBBER WASHER
ARANDELA DE
CAUCHO
FLAT WASHER
ARANDELA PLANA
HEXNUT
TUERCA HEXAGONAL
INSTRUCTIONS FOR MOUNTING FIXTURE OUTDOORS AND/
OR IN WET LOCATIONS.
17) Mounting surface should be clean, dry, flat and 1/4” larger
that the canopy on all sides. Any gaps between the mounting
surface and canopy exceeding 3/16” should be corrected
as required.
18) With silicone caulking compound, caulk completely around
where back of canopy meets the wall surface to prevent
water from seeping into outlet box.