Kichler 65382 - Manual

MOUNTING STRAP
ABRAZADERA DE
MONTAJE
SEMI FLUSH INSTALLATION INSTRUCTIONS
1) Screw end of threaded pipe into coupling on top of fixture body.
2) Lower tube down over threaded pipe.
3) Pass hole in check ring over end of threaded pipe. Set check ring on
top of tube.
4) Lower top trim down over end of threaded pipe.
5) Slip lockwasher over end of threaded pipe.
6) Thread hex coupling onto end of threaded pipe.
7) Thread end of short threaded pipe into end of hex coupling.
8) Pass hole in canopy over end of threaded pipe. Set canopy on top of
top trim.
9) Slip lockwasher over end of threaded pipe. Thread hexnut onto
threaded pipe.
10) Follow steps #13-27 in Stem Drop Installation Instructions.
STEM DROP INSTALLATION INSTRUCTIONS
1) Pass fixture wire through long threaded pipe.
2) Screw end of long threaded pipe into coupling on top of fixture body.
3) Lower tube down over threaded pipe.
4) Pass hole in check ring over end of threaded pipe. Set check ring on
top of tube.
5) Screw coupling onto end of threaded pipe.
6) Pass wire from fixture though stem and screw stem to top of fixture.
NOTE: Thread locking compound must be applied to all stem
threads as noted with symbol (3) to prevent accidental rotation of fixture
during cleaning, relamping, etc.
7) Pass fixture wire through remaining stems and screw stems together.
8) Thread one small threaded pipe into end of each small loop.
9) Attach small loop to end of last stem.
10) Pass threaded pipe at end of second small loop through hole in canopy.
11) Slip lockwasher over threaded pipe protruding from inside of canopy
and screw hexnut onto threaded pipe.
12) Attach chain link to small loop at end of stem and to loop on canopy.
13) TURN OFF POWER.
IMPORTANT: Before you start, NEVER attempt any work without
shutting off the electricity until the work is done.
a) Go to the main fuse, or circuit breaker, box in your home. Place
the main power switch in the “OFF” position.
b) Unscrew the fuse(s), or switch “OFF” the circuit breaker switch(s),
that control the power to the fixture or room that you are working on.
c) Place the wall switch in the “OFF” position. If the fixture to be
replaced has a switch or pull chain, place those in the “OFF”
position.
14) Find the appropriate threaded holes on mounting strap. Assemble
mounting screws into threaded holes.
15) Attach mounting strap to outlet box. (Screws not provided). Mounting
strap can be adjusted to suit position of fixture.
16) Grounding instructions: (See Illus. A or B).
A) On fixtures where mounting strap is provided with a hole and two
raised dimples. Wrap ground wire from outlet box around green
ground screw, and thread into hole.
B) On fixtures where a cupped washer is provided. Attach ground
wire from outlet box under cupped washer and green ground
screw, and thread into mounting strap.
If fixture is provided with ground wire. Connect fixture ground wire to
outlet box ground wire with wire connector. (Not provided.) After
following the above steps. Never connect ground wire to black or
white power supply wires.
17) Make wire connections (connectors not provided.) Reference chart
below for correct connections and wire accordingly.
18) Push fixture to ceiling, carefully passing mounting screws through holes
in canopy.
19) Secure fixture to ceiling with threaded balls.
20) Insert recommended bulbs.
21) Raise shade up to fixture. Align holes in bracket on shade with holes
in bracket on fixture body.
22) Thread ball studs down through holes in bracket. Tighten ball studs
to secure shade in place.
23) Screw short end of threaded pipe with hexnut into coupling at bottom
of fixture.
24) Slip flat washer then rubber washer over end of threaded pipe.
25) Pass hole in diffuser over end of threaded pipe.
26) Slip remaining rubber washer then flat washer over end of threaded
pipe. Screw hexnut onto threaded pipe.
27) Pass bottom trim over end of threaded pipe. Screw finial onto
threaded pipe. (DO NOT over tighten.)
GREEN GROUND
SCREW
CUPPED
WASHER
A B
OUTLET BOX
GROUND
FIXTURE
GROUND
DIMPLES
WIRE CONNECTOR
(NOT PROVIDED)
OUTLET BOX
GROUND
GREEN GROUND
SCREW
FIXTURE
GROUND
Connect Black or
Red Supply Wire to:
Connect
White Supply Wire to:
Black White
*Parallel cord (round & smooth) *Parallel cord (square & ridged)
Clear, Brown, Gold or Black
without tracer
Clear, Brown, Gold or Black
with tracer
Insulated wire (other than green)
with copper conductor
Insulated wire (other than green)
with silver conductor
*Note: When parallel wires (SPT I & SPT II)
are used. The neutral wire is square shaped
or ridged and the other wire will be round in
shape or smooth (see illus.)
Neutral Wire
Date Issued: 11/16/12 IS-65382-US
CANOPY
ESCUDETE
STEM
VÁSTAGO
KNURL KNOB
PERILLA ESTRADA
3
SMALL LOOP
ARGOLLA PEQUEÑA
CHAIN LINK
ESLABÓN DE CADENA
3
THREADED PIPE
TUBO ROSCADO
BOTTOM TRIM
GUARNICIÓN INFERIOR
FINIAL
CAPUCHON
HEXNUT
TUERCA HEXAGONAL
FLAT WASHER
ARANDELA PLANA
FLAT WASHER
ARANDELA PLANA
RUBBER WASHER
ARANDELA DE CAUCHO
DIFFUSER
DIFUSOR
STEM MOUNT INSTALLTION
INSTALACIÓN DEL VÁSTAGO DE MONTAJE
SEMI FLUSH INSTALLATION
INSTALACIÓN DEL SEMI-RAS
MOUNTING STRAP
ABRAZADERA DE MONTAJE
CANOPY
ESCUDETE
KNURL KNOB
PERILLA ESTRADA
SEE OTHER SIDE FOR SPANISH TRANSLATIONS.
VEA EL OTRO LADO DE TRADUCCIONES AL ESPAÑOL.
TOP TRIM
GUARNICIÓN SUPERIOR
COUPLING
ACOMPLAMIENTO
HEXNUT
TUERCA HEXAGONAL LOCKWASHER
ARANDELA DE
SEGURIDAD
SHADE
PANTALLA
TUBE
TUBO
CHECK RING
ANILLO DE SEGURIDAD
BRACKET
PEDESTAL
BALL STUD
ESPÁRRAGO DE
CABEZA ESFÉRICA
HEXNUT
TUERCA HEXAGONAL
LOCKWASHER
ARANDELA DE SEGURIDAD
TUBE
TUBO
CHECK RING
ANILLO DE SEGURIDAD
THREADED PIPE
TUBO ROSCADO
THREADED PIPE
TUBO ROSCADO
HEX COUPLING
ACOPLAMIENTO
HEXAGONAL